23/07/2024 17:35:58

Windshield Harness - Harness - Glass Assembly (Remove and Install)

Correction code 1710134011 1710134012 FRT 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Cybertruck electronics are powered by a 48V "mid voltage" or "MV" architecture that is designed to improve efficiency. Servicing MV components requires extra knowledge and care in order to avoid personal and/or vehicular harm. Read and understand MV precautions in Electrical Precautions and make sure any required MV-related training courses have been completed, as applicable.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  3. Disconnect MV power. See Disconnect MV Power.
  4. Remove the front header trim. See Headliner Trim - Front Header Trim (Remove and Install).
  5. Pivot the LH and RH visors to sides.
    Figure 1. LH shown; RH similar
  6. Remove the rearview mirror. See Rearview Mirror - Rear View Miror (Remove and Install).
  7. Remove the rearview mirror beauty cover. See Rearview Mirror - Beauty Cover (Remove and Install).
  8. Release the connector lock, and then disconnect the GNSS antenna.
  9. Release the connector locks, and then disconnect the forward facing camera assembly connectors (x2).
  10. Gently pull the PRND + Hazard switch assembly downward to release the clips (x2), and then disconnect the electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not allow the assembly to hang from the harness.
  11. Disconnect the windshield harness electrical connectors (x4), release the harness clips (x6), and then remove the harness from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the harness bracket from overhead console bracket.

Install

  1. Position the windshield harness into the vehicle, connect the electrical connectors (x4), and then secure the harness clips (x6).
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the harness bracket to overhead console bracket.
  2. Position the PRND + Hazard switch assembly into the vehicle, connect the electrical connector, and then press the assembly upward to secure the clips (x2).
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not allow the assembly to hang from the harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace any missing or damaged clips.
  3. Connect the forward facing camera assembly connectors (x2), and then engage the connector locks.
  4. Connect the GNSS antenna, and then engage the connector lock.
  5. Install the rear view mirror beauty cover. See Rearview Mirror - Beauty Cover (Remove and Install).
  6. Install the rear view mirror. See Rearview Mirror - Rear View Miror (Remove and Install).
  7. Move the LH and RH visors back to their original positions.
  8. Install the front header trim. See Headliner Trim - Front Header Trim (Remove and Install).
  9. Reconnect MV power. See Disconnect MV Power.
  10. Install the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  11. Raise the LH front window and close the LH front door.