23/07/2024 17:23:31

2nd Row Seat Back Hardware - 2R Seat Underbelly RH (Remove and Install)

Correction code 1305003071 1305003072 FRT 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Cybertruck electronics are powered by a 48V "mid voltage" or "MV" architecture that is designed to improve efficiency. Servicing MV components requires extra knowledge and care in order to avoid personal and/or vehicular harm. Read and understand MV precautions in Electrical Precautions and make sure any required MV-related training courses have been completed, as applicable.

Remove

  1. Open all the doors and lower all the windows.
  2. Move the LH and RH front seats fully forward.
  3. Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  4. Disconnect MV power. See Disconnect MV Power.
  5. Remove the RH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  6. Remove the RH upper A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Upper Trim - LH (Remove and Install).
  7. Remove the RH cantrail trim. See Headliner Trim - Cantrail Trim - LH (Remove and Install).
  8. Remove the rear wall lower trim. See Passenger Compartment Carpet - End Item, Rear Wall Lower Trim, Soft Trim (Remove and Install).
  9. Fold the LH and RH 2nd row seats down.
  10. Remove the RH upper C-pillar trim. See A-B-C Post Interior Trim - C-Pillar Upper Trim - LH (Remove and Install).
  11. Release the clips (x7) and datum that attach the RH 2nd row shoulder cover to the vehicle, and then remove the cover from the vehicle.
  12. Remove the RH 2nd row seat back outboard bolster. See 2nd Row Seat Assemblies - 2R Seat Side Bolster LH (Remove and Install).
  13. Remove the RH 2nd row seat back inboard bolster. See 2nd Row Seat Assemblies - 2R Seat Back Inboard Bolster LH (Remove and Install).
  14. Remove the clip that attaches the RH 2nd row seat cushion release buckle strap guide to the vehicle, and then release the guide from the vehicle.
  15. Remove the bolts (x3) and clips (x4) that attach the RH 2nd row seat back assembly to the vehicle.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  16. Lift the RH 2nd row seat back upwards and away from the seat frame, disconnect the seat back electrical connector, and then remove the seat back from the vehicle.
  17. Release the clip that attaches the RH 2nd row seat cushion outboard cover to the seat assembly, and then remove the cover from the assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull outward from lower forward section to release.
  18. Release the RH 2nd row seat cushion from the underbelly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull plastic retainers outward to release from underbelly.
  19. Release the clips (x4) that attach the RH 2nd row seat underbelly to the seat cushion assembly, and then remove the underbelly trim from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull outwards from the bottom to release.

Install

  1. Position the 2nd row seat cushion underbelly onto the seat cushion assembly, and then engage the clips (x4).
    Informational PurposesAn informational icon, calling your attention
    Note
    Push inwards firmly to secure.
  2. Push the plastic retainers into the grooves to secure the LH 2nd row seat cushion to the underbelly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Manipulate the material as needed to engage all the retainers.
  3. Position the RH 2nd row seat cushion outboard cover to the seat assembly, and then engage the clip that attaches the cover to the assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push inwards at bottom to secure.
  4. Position the RH 2nd row seat back into the vehicle, and then connect the seat back electrical connector and engage the connector lock.
  5. Position the RH 2nd row seat back assembly into the seat frame, and then install the bolts (x3) and clips (x4) that attach the seat back to the vehicle.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  6. Maneuver the RH 2nd row seat cushion release buckle strap guide into position, and then install the clip that attaches the guide to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the strap is not twisted.
  7. Install the RH 2nd row seat back inboard bolster. See 2nd Row Seat Assemblies - 2R Seat Back Inboard Bolster LH (Remove and Install).
  8. Install the RH 2nd row seat back outboard bolster. See 2nd Row Seat Assemblies - 2R Seat Side Bolster LH (Remove and Install).
  9. Position the RH 2nd row shoulder cover into the vehicle, and then engage the clips (x7) and datum that attach the cover to the vehicle.
  10. Install the RH upper C-pillar trim. See A-B-C Post Interior Trim - C-Pillar Upper Trim - LH (Remove and Install).
  11. Install the rear wall lower trim. See Passenger Compartment Carpet - End Item, Rear Wall Lower Trim, Soft Trim (Remove and Install).
  12. Install the RH cantrail trim. See Headliner Trim - Cantrail Trim - LH (Remove and Install).
  13. Install the RH upper A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Upper Trim - LH (Remove and Install).
  14. Install the RH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  15. Reconnect MV power. See Disconnect MV Power.
  16. Install the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  17. Restore the LH and RH front seats back to their original position.
  18. Raise all the windows and close all the doors.