2025-06-11

Bed Side Outer Assembly - LH (Long Range) (Remove and Install)

Correction code NEW NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning

This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Warning

Cybertruck electronics are powered by a 48V "mid voltage" or "MV" architecture that is designed to improve efficiency. Servicing MV components requires extra knowledge and care in order to avoid personal and/or vehicular harm. Read and understand MV precautions in Electrical Precautions and make sure any required MV-related training courses have been completed, as applicable.

2025-05-05: Released new procedure.

Open all 4 doors

Note
Push pillar door triggers to release
Lower all 4 windows
Manually latch all doors to prevent lockout

Note
Engage latch with screwdriver
Run ODIN routine PROC_ICE_X_ENTER-SERVICE-MODEvia Toolbox: (link)
Open tailgate

Note
Press button to release
Open powered front trunk

Note
Via exterior switch or UI
Remove rear underhood apron

Note
9x clips
Disconnect FRL connector then disconnect MV battery connector

Note
2x connectors, Release locking tab then disconnect FRL connector, Slide eCPA to left then lift lever to release MV battery connector, Early production trucks may have black FRL connector, Release eCPA by pushing down to unlock and slide red locking tab, Wait 2 minutes for electrical circuits to discharge before disconnecting modules
Remove frunk assembly

Note
6x bolts, 10mm, 12 Nm, 2x bolt caps, 2x bumpstops, 1x connector, Remove bolt covers from frunk floor, Remove washer fluid cap by gently prying upwards, Rotate bumpstops counter clockwise to release, the 25mm socket from PT Sensor kit can be used, Avoid straining emergency frunk release connector
Remove LH underhood apron

Note
3x clips
Remove front nut securing LH cantrail

Note
1x nut, 8mm, 4 Nm, Discard after removal
Remove LH header seal

Note
Seal begins at front quarter glass and ends at C-pillar applique, Start at C-pillar, Pull B-pillar applique down gently to release seal, Pull outwards to release seal from carrier grooves
Remove screws securing LH cantrail

Note
8x screws, T20, 2.5 Nm, Pull C-pillar applique down as required for access
Remove LH cantrail assembly

Note
7x clips, Recommend assistance, Pull away from body side to release clips, Place on padded surface
Remove LH sail baffle applique

Note
3x clips, Release clips working from bottom upwards
Remove LH sail baffle closeout

Note
6x clips
Remove LH rear fore fender flare

Note
12 clips, 9x tabs
Remove clips securing LH rear wheel liner to fore fender flare carrier

Note
5x clips
Remove LH rear fore fender flare carrier

Note
6x bolts, 10mm, 7 Nm, 1x connector, Disconnect BLE module then remove carrier, Release locking tab
Remove LH rear aft fender flare

Note
5x clips
Remove clips securing LH rear wheel liner to aft fender flare carrier

Note
2x clips
Remove LH rear aft fender flare carrier

Note
2x bolts, 10mm, 7 Nm, 2x datum
Remove chargeport door

Note
1x bolts, 10mm, 6 Nm, 1x connector, 1x datum, Rotate up and out of sail
Remove fastener covers from bed floor assembly

Note
14x covers
Remove bed floor assembly

Note
10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Lift front edge with trim tool then remove panel, Recommend assistance
Remove LH sail applique

Note
15x clips, 1x connector, 1x harness clip, Lift rear edge first to remove connector and harness clip
Remove LH upper bed side wall assembly

Note
13x clips, Start from rear, Pull from the bottom downwards
Remove LH bed closeout panel

Note
6x clips, 1x tab, Release LH tailgate cable by disengaging lock spring from bolt and sliding cable eyelet off to allow removal of bed closeout panel from vehicle
Remove LH lower bed side wall

Note
2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers
Remove LH outer bed side

Note
13x bolts, 13mm, 28 Nm, 1x screw, T25, 8 Nm, Assistance required, Have assistant hold bed side to body while bolts are removed, Place on padded surface once removed
Install LH outer bed side

Note
13x bolts, 13mm, 28 Nm, 1x screw, T25, 8 Nm, Assistance required, Have assistant hold panel against body then install bolts hand tight, Adjust gap and flush as required then torque bolts
Install LH lower bed side wall

Note
2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers
Install LH bed closeout panel

Note
6x clips, 1x tab, Secure LH tailgate cable once closeout installed
Install LH upper bed side wall assembly

Note
13x clips, Replace any missing or damaged clips, Lift tonneau seal as required
Install LH sail applique

Note
15x clips, 1x connector, 1x harness clip, Replace any broken clips
Install bed floor assembly

Note
10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Recommend assistance
Install fastener covers onto bed floor assembly

Note
14x covers
Install bolts securing chargeport assembly onto body

Note
2x bolts, 10mm, 6 Nm, Use only hand tools, Risk of galling if power tools are used on stainless fasteners
Install chargeport door

Note
1x bolts, 10mm, 6 Nm, 1x connector, 1x datum
Install LH rear fore fender flare carrier

Note
6x bolts, 10mm, 7 Nm, 1x connector, Connect BLE then install carrier, Engage locking tab
Install clips securing LH rear wheel liner to fore fender flare carrier

Note
5x clips
Install clips securing LH rear wheel liner to aft fender flare carrier

Note
2x clips
Install both LH rear fore and aft fender flares

Note
12 clips, 9x tabs
Instal LH sail baffle closeout

Note
6x clips, Replace any missing or damaged clips
Install LH sail baffle applique

Note
3x clips, Replace any missing or damaged clips
Install LH cantrail assembly

Note
7x clips, Recommend assistance, Vehicles may be equipped with 10 or 11 clips in production range
Install screws securing LH cantrail

Note
8x screws, T20, 2.5 Nm, Pull C-pillar applique down as required for access
Install LH header seal

Note
Start from front quarter glass, Push upwards into seal carrier grooves
Install nut securing LH front outer cantrail

Note
1x nut, 8mm, 4 Nm, Install new nut
Install LH underhood apron

Note
3x clips, Replace any missing or damaged clips
Connect FRL connector then connect MV battery connector

Note
2x connectors, Connect FRL connector then secure locking tab, Position lever to secure MV battery connector then slide eCPA to right, Early production trucks may have black FRL connector, If power cycling vehicle then ensure at least 60 seconds has passed since powering down
Install frunk assembly

Note
6x bolts, 10mm, 12 Nm, 2x bolt caps, 2x bumpstops, 1x connector, Install bolt covers to frunk floor, Install washer fluid cap, Install bumpstops by aligning tabs then turning clockwise, Ensure emergency frunk release functions
Install rear underhood apron

Note
9x clips, Adjust windshield seal as required
Close powered front trunk

Note
Via exterior switch or UI
Run ODIN routine PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox: (link)
Raise all 4 windows
Close all 4 doors
Close tailgate

Cybertruck Service Manual

Bed Side Outer Assembly - LH (Long Range) (Remove and Install)

Figure 1

Figure 2

Figure 3