2025-11-11

SCUBA Valve Block Assembly (Remove and Install)

Correction code 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2025-11-10: VOSS fittings are reusable. Removed steps that instructed to discard fitting.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.
  1. Use the vehicle touchscreen to depressurize the TAS system. See Pressurize / Depressurize - Full System (Test/Adjust).
  2. Remove the bed floor assembly. See Bed Floor Assembly (Remove and Install).
  3. Release ANC air line from pressurized pack valve block
    Informational PurposesAn informational icon, calling your attention
    Note
    1x VOSS fitting, 12mm, 8 Nm, Do not release air line to reservoir, Rapid loss of pressure will result if wrong air line is released
  4. Release RES 2 air line from pressurized pack valve block
    Informational PurposesAn informational icon, calling your attention
    Note
    1x VOSS fitting, 10mm, 8 Nm
  5. Remove pressurized pack valve block
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 5 Nm, 1x connector, 2x datums
  6. Install pressurized pack valve block
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 5 Nm, 1x connector, 2x datums
  7. Secure RES 2 air line onto pressurized pack valve block
    Informational PurposesAn informational icon, calling your attention
    Note
    1x line, Remove plastic cap from VOSS fittings, Press air lines onto fitting until mark aligns with top of fitting, Verify line is properly secured by performing push and pull test
  8. Secure ANC air line onto pressurized pack valve block
    Informational PurposesAn informational icon, calling your attention
    Note
    1x line, Remove plastic cap from VOSS fittings, Press air lines onto fitting until mark aligns with top of fitting, Verify line is properly secured by performing push and pull test
  9. Install the bed floor assembly. See Bed Floor Assembly (Remove and Install).
  10. Pressurize the TAS system but do not exit Service Mode. See Pressurize / Depressurize - Full System (Test/Adjust).
  11. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  12. Click the Actions tab and search for "Pressurize".
  13. Click Tesla Air Suspension Pressurize HV Pack, click Run, and allow routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Select "X" at top right of window to close once complete, If reservoir air pressure is not ~16 bar then proceed to full system pressurize procedure, If pack is not able to maintain pressure post test then proceed to Pressurized Pack Not Holding Pressure inspection procedure, If pack is taking too long to pressurize then proceed to find leak
  14. Disconnect Toolbox and remove the laptop from the vehicle. See Toolbox 3 (Connect and Disconnect).
  15. Exit Service Mode. See Service Mode.
  16. Raise the LH front window and close the LH front door.