23/07/2024 17:27:14

Closure Panels - Assembly - Sail Complete - Left (Remove and Install)

Correction code 1010025101 FRT 1.38 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Cybertruck electronics are powered by a 48V "mid voltage" or "MV" architecture that is designed to improve efficiency. Servicing MV components requires extra knowledge and care in order to avoid personal and/or vehicular harm. Read and understand MV precautions in Electrical Precautions and make sure any required MV-related training courses have been completed, as applicable.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Put the vehicle in Service Mode. See Service Mode.
  3. Open the LH rear door.
  4. Open the tonneau cover.
  5. Open the tailgate.
  6. Open the powered frunk.
  7. Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  8. Disconnect MV power. See Disconnect MV Power.
  9. Remove the frunk. See Frunk Assembly (Remove and Install).
  10. Remove the LH underhood apron. See Underhood Trim - Side Apron Assembly - LH (Remove and Install).
  11. Remove the LH cantrail. See Closure Panels - Assembly - Cantrail - Left (Remove and Install).
  12. Remove the LH sail baffle applique. See Exterior Trim Fittings - Sail Baffle Applique - LH (Remove and Install).
  13. Remove the LH sail baffle closeout. See Exterior Trim Fittings - Sail Baffle Closeout - LH (Remove and Install).
  14. Remove LH rear fore fender flare. See Front and Rear Garnish - Rear Fender Flare Fore - LH (Remove and Install).
  15. Remove the LH rear fore fender flare carrier. See Front and Rear Garnish - Carrier - Rear Fender Flare Fore - LH (Remove and Install).
  16. Remove the LH rear aft fender flare. See Front and Rear Garnish - Rear Fender Flare Aft - LH (Remove and Install).
  17. Remove LH rear aft fender flare carrier. See Front and Rear Garnish - Carrier - Rear Fender Flare Aft - LH (Remove and Install).
  18. Remove the charge port door. See Charge Port - Charge Port Door (Remove and Install).
  19. Remove the bolts (x2) that attach the charge port assembly to the body.
    6 Nm (4.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only hand tools. Risk of galling if power tools are used on stainless fasteners.
  20. Remove the fastener covers (x10) from the forward bed panel.
  21. Remove the bolts (x10) that attach the forward bed panel to the vehicle.
    56 Nm (41.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift the front edge with trim tool, and then remove the panel.
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance to hand off the panel.
  22. Remove the LH sail applique. See Truck Bed Exterior Trim - Sail Applique Assembly - LH (Remove and Replace).
  23. Release the clip, and then remove the LH tonneau rail seal.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull away from the rail to release it from the groove.
  24. Remove the LH rear lamp closeout applique. See Truck Bed Exterior Trim - Rear Lamp Closeout Applique - LH (Remove and Install).
  25. Remove the LH upper bed side wall assembly. See Truck Bed Exterior Trim - Upper Bed Side Wall Assembly - LH (Remove and Install).
  26. Remove the LH rear bed closeout. See Truck Bed - Rear Bed Closeout - LH (Remove and Install).
  27. Remove the LH bed side wall.
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance.
    Informational PurposesAn informational icon, calling your attention
    Note
    x1 bolt, 15 mm, 46 Nm; x2 bolts, T45, 36 Nm; x4 bolts, 10 mm, 11 Nm; x2 nuts, 10 mm, 7 Nm; x4 clips, x1 fastener cover
    Informational PurposesAn informational icon, calling your attention
    Note
    x1 electrical connector. Release the locking tab.
    Informational PurposesAn informational icon, calling your attention
    Note
    Disconnect the bed outlet electrical connectors from the bed side wall and ground strap (x1 bolt, 10 mm, 10 Nm, x2 electrical connectors); release locking tabs, slide lock to release.
  28. Remove the LH outer bed side.
    Informational PurposesAn informational icon, calling your attention
    Note
    x13 bolts, 13 mm, 28 Nm; x1 screw, T30, 8 Nm
    Informational PurposesAn informational icon, calling your attention
    Note
    Assistance required: Have assistant hold the panel to the body while bolts are removed.
    Informational PurposesAn informational icon, calling your attention
    Note
    Place the outer bed side on a padded surface once removed.

Install

  1. Install the LH outer bed side.
    Informational PurposesAn informational icon, calling your attention
    Note
    x13 bolts, 13 mm, 28 Nm; x1 screw, T30, 8 Nm
    Informational PurposesAn informational icon, calling your attention
    Note
    Assistance required. Have assistant hold the panel against the body, and then install the bolts hand tight. Adjust gap and flush as required, and then torque the bolts.
  2. Install the LH bed side wall.
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance.
    Informational PurposesAn informational icon, calling your attention
    Note
    x1 bolt, 15 mm, 46 Nm; x2 bolts, T45, 36 Nm; x4 bolts, 10 mm, 11 Nm; x2 nuts, 10 mm, 7 Nm; x4 clips, x1 fastener cover, x1 electrical connector
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the locking tabs. Connect the bed outlet electrical connectors to bed side wall and ground strap (x1 bolt, 10 mm, 10 Nm, x2 electrical connectors). Secure locking tabs. Slide lock to secure.
  3. Install the LH rear bed closeout. See Truck Bed - Rear Bed Closeout - LH (Remove and Install).
  4. Install the LH upper bed side wall assembly. See Truck Bed Exterior Trim - Upper Bed Side Wall Assembly - LH (Remove and Install).
  5. Install the LH rear lamp closeout applique. See Truck Bed Exterior Trim - Rear Lamp Closeout Applique - LH (Remove and Install).
  6. Install the LH tonneau rail seal.
    Informational PurposesAn informational icon, calling your attention
    Note
    x1 clip
    Informational PurposesAn informational icon, calling your attention
    Note
    Push seal into the rail groove.
  7. Install the LH sail applique. See Truck Bed Exterior Trim - Sail Applique Assembly - LH (Remove and Replace).
  8. Install the bolts (x10) that attach the forward bed panel to the body.
    56 Nm (41.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance for installation.
  9. Install fastener covers (x10) on the forward bed panel.
    Informational PurposesAn informational icon, calling your attention
    Note
    Figure needs to be updated to show 10 bolts.
  10. Install the bolts (x2) that attach the charge port assembly to the body.
    6 Nm (4.4 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only hand tools. Risk of galling if power tools are used on stainless fasteners.
  11. Install the charge port door. See Charge Port - Charge Port Door (Remove and Install).
  12. Install the LH rear fore fender flare carrier. See Front and Rear Garnish - Carrier - Rear Fender Flare Fore - LH (Remove and Install).
  13. Install the LH rear aft fender flare. See Front and Rear Garnish - Rear Fender Flare Aft - LH (Remove and Install).
  14. Install the LH rear fender aft flare carrier. See Front and Rear Garnish - Carrier - Rear Fender Flare Aft - LH (Remove and Install)
  15. Install the LH rear aft fender flare. See Front and Rear Garnish - Rear Fender Flare Aft - LH (Remove and Install).
  16. Install the LH sail baffle closeout. See Exterior Trim Fittings - Sail Baffle Closeout - LH (Remove and Install).
  17. Install the LH sail baffle applique. See Exterior Trim Fittings - Sail Baffle Applique - LH (Remove and Install).
  18. Install the LH cantrail. See Closure Panels - Assembly - Cantrail - Left (Remove and Install).
  19. Install the LH underhood apron. See Underhood Trim - Side Apron Assembly - LH (Remove and Install).
  20. Reconnect MV power. See Disconnect MV Power.
  21. Install the frunk. See Frunk Assembly (Remove and Install).
  22. Install the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  23. Close the powered frunk.
  24. Close the LH rear door.
  25. Exit Service Mode. See Service Mode.
  26. Raise the LH front window and close the LH front door.
  27. Close the tonneau cover.
  28. Close the tailgate.