Busbar - Charge Port (Standard) (Remove and Replace)
Correction code
NEW
NOTE: Unless
otherwise explicitly stated in the procedure, the correction code and its
associated FRT reflect all of the work required to perform this procedure,
including the linked procedures. Do not stack correction
codes unless explicitly told to do so.
NOTE: See Flat Rate Times to
learn more about FRTs and how they are created.
NOTE: See Personal Protection to make
sure you are wearing proper PPE when performing the procedure below.
NOTE: See Ergonomic Precautions for safe and healthy
working practices.
High Voltage Awareness Care Pointsfor additional glove and safety information.
- 2026-05-08: Released new procedure.
- Open the tonneau cover.
- Open the tailgate.
- Open the LH front door and lower the LH front window.
- Open the powered frunk.
- Use the vehicle touchscreen to open charge port door.
- Disconnect MV power. See Mid-Voltage Power (Disconnect and Connect) (Modify).
-
Verify operation of multimeter
NoteSet multimeter to DC voltage, Confirm multimeter is properly measuring voltage by testing MV battery, Touch lightly and do not damage terminals
-
Remove all items from pockets and ensure not wearing metal items
NoteThis includes phones, badges, metal belt buckles airpods and headphones
-
Inspect HV insulating gloves
NoteCheck gloves for damage prior to use, Refer to service document TN-15-92-003, for information on inspecting HV gloves.
-
Put on HV insulating gloves and leather over gloves
NoteUse HV cut resistant insulated gloves or HV insulating gloves and leather over gloves, HV Insulating gloves must be worn any time a Hioki Tester or Hi-Pot Tester is used, Refer to service document TN-15-92-003 R5 for PPE requirements depending on vehicle configuration
-
Verify there is no high voltage present at the charge port
NoteMeasure B+ to B-, and B+ to Ground and B - to Ground, Place Alligator clip onto body panel
- Remove leather over gloves and HV insulating gloves
- Remove the LH rear fore fender flare. See Fender Flare - Fore - Rear - LH (Remove and Install).
- Remove the LH rear aft fender flare. Se Fender Flare - Aft - Rear - LH (Remove and Install).
- Remove the LH rear aft fender flare carrier. See Carrier - Fender Flare - Aft - Rear - LH (Remove and Install).
- Remove the LH rear fore fender flare carrier. See Carrier - Fender Flare - Fore - Rear - LH (Remove and Install).
- Remove the bed floor assembly. See Bed Floor Assembly (Long Range) (Remove and Install).
- Remove the LH sail applique. See Sail Applique - LH (Remove and Install) (Post 11/4/2024).
- Remove the LH tonneau water management seal. See Water Management Seal - LH - Center - Tonneau (Remove and Install).
- Remove the LH upper bed side wall. See Bed Side Wall Assembly - Upper - LH (Remove and Install).
- Remove the LH rear bed closeout. See Bed Closeout - Rear - LH (Remove and Install).
- Remove the LH lower bed side wall. See Bed Side Wall - LH (Standard) (Remove and Install).
-
Remove the bolt that attaches the busbar
HV connector lid.
9 Nm (6.6 lbs-ft)NoteEP10 -
Remove the bolts (x2) that attach the HV
connector to the DC FC header.
9 Nm (6.6 lbs-ft)TipUse of the following tool(s) is recommended:- 10 mm socket
-
Release the HV connector from the DC FC
header, and then use an inflatable airbag to suspend the busbar assembly above the
ancillary assembly.
-
Disconnect the charge port assembly
electrical connector.
NoteRemove the white locking tab. Press the tab to release the connection from the charge port. Continue to pull off connector. The charge port connection is intended to disengage the safety cap when released.NoteDo not push down on the red tab. Pull the red tab to disengage lock. Pull again to release the electrical connector.
-
Release the clip and disconnect the
charge port door LV electrical connectors (x2).
-
Remove the bolt that attaches the ground
cable to the busbar assembly.
6.5 Nm (4.8 lbs-ft)TipUse of the following tool(s) is recommended:- 10 mm socket
-
Remove the bolt that attaches the charge
port to the outer sail.
6.5 Nm (4.8 lbs-ft)TipUse of the following tool(s) is recommended:- 10 mm deep socket
-
Remove the bolts (x2) that attach the
charge port assembly onto the body.
6 Nm (4.4 lbs-ft)TipUse of the following tool(s) is recommended:- 10 mm 12-point deep socket
CAUTIONUse only hand tools. Risk of galling if power tools are used on stainless bolts. -
Remove the charge port and busbar
assembly from the vehicle.
-
Clean the DC FC header contact surface
of residual Penetrox with an Isopropyl Alcohol (IPA) wipe.
NoteAllow 1 minute dry time after removing Penetrox.
-
Clean the busbar HV connector contact
surface of residual Penetrox.
NoteAllow 1 minute dry time after removing Penetrox.NoteIt is necessary to clean the HV connector during reuse of the busbar.
-
Apply Penetrox onto the HV connector
joints.
NoteApply 2 drops of Penetrox A-13 about 5 mm in diameter to either side of the hole on both leads. Spread evenly to verify the contact surface is fully covered.
-
Position the charge port busbar assembly
onto the vehicle.
-
Install the bolts (x2) that attach the
charge port busbar kit to the HV header.
9 Nm (6.6 lbs-ft)TipUse of the following tool(s) is recommended:- 10 mm socket (insulated)
-
Perform a Hioki resistance test at each
HV joint from the HV busbar lead to the bolt head.
Notex2 HV jointsNoteWhen using a Hioki tester, verify the meter has been properly adjusted and set prior to usage.NoteThe acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).
- If the resistance is greater than 0.195 mΩ (195 μΩ), there is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again.
- If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.
- If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), the Hioki test passed. proceed to the next step.
-
Install the bolt that attaches the
busbar HV connector lid.
9 Nm (6.6 lbs-ft)TipUse of the following tool(s) is recommended:- 10 mm socket
-
Install the bolts (x2) that attach the
charge port assembly onto the body.
6 Nm (4.4 lbs-ft)TipUse of the following tool(s) is recommended:- 10 mm 12-point deep socket
CAUTIONUse only hand tools. Risk of galling if power tools are used on stainless bolts. -
Install the bolt that attaches the
charge port to the outer sail.
6.5 Nm (4.8 lbs-ft)TipUse of the following tool(s) is recommended:- 10 mm deep socket
-
Install the bolt that attaches the
busbar ground to the body.
6.5 Nm (4.8 lbs-ft)TipUse of the following tool(s) is recommended:- 10 mm socket
-
Connect the charge port door electrical
connectors (x2) and fasten clip.
-
Connect the charge port electrical
connector.
NoteFully engage the connection and white locking tab. The electrical connector is intended to lock the safety cap in place.
- Install the LH lower bed side wall. See Bed Side Wall - LH (Standard) (Remove and Install).
- Install the LH rear bed closeout. See Bed Closeout - Rear - LH (Remove and Install).
- Install the LH upper bed side wall. See Bed Side Wall Assembly - Upper - LH (Remove and Install).
- Install the LH tonneau water management seal. See Water Management Seal - LH - Center - Tonneau (Remove and Install).
- Install the LH sail applique. See Sail Applique - LH (Remove and Install) (Post 11/4/2024).
- Install the LH rear fore fender flare carrier. See Carrier - Fender Flare - Fore - Rear - LH (Remove and Install).
- Install the bed floor assembly. See Bed Floor Assembly (Long Range) (Remove and Install).
- Install the LH rear aft fender flare carrier. See Carrier - Fender Flare - Aft - Rear - LH (Remove and Install).
- Install the LH rear fore fender flare. See Fender Flare - Fore - Rear - LH (Remove and Install).
- Install the LH rear aft fender flare. See Fender Flare - Aft - Rear - LH (Remove and Install).
- Reconnect MV power. See Mid-Voltage Power (Disconnect and Connect) (Modify).
- Install the rear underhood apron. See Underhood Apron - Rear (Remove and Install).
- Raise the LH front window and close the LH front door.
- Close the tonneau cover.
- Close the tailgate.