Rear Knuckle - Hub and Bearing - Driven Hub - 6X139.7mm PCD - 180mm Flange (Remove and Install)
Correction code 3103097011 FRT 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
Bolts (x2) that attach the LH rear brake caliper to the LH rear knuckle |
|
|
Reuse | |
Bolt that attaches the LH rear wheel speed sensor to the LH rear knuckle |
|
|
Reuse | |
Bolts (x4) that attach the LH rear hub to the LH rear knuckle |
|
|
Reuse |
Remove
- Open the LH front door and lower the LH front window.
- Raise and support the vehicle on a 2 post lift. See Raise Vehicle - 2 Post Lift.
- Remove the LH rear wheel center cap. See Wheel Cover - Front - LH (Remove and Install).
- Remove the LH rear wheel. See Wheel Assembly (Remove and Install).
-
Release the connector lock, and then
disconnect the rear left chassis corner harness electrical connector from the brake
caliper.
-
Remove the bolt that attaches the LH
rear wheel speed sensor to the LH rear knuckle, and then release the harness clips
(x2).Tip: Use of the following tool(s) is recommended:
- Torx T30 socket
-
Connect the EPB harness electrical
connector to the LH rear brake caliper, and then engage the connector lock.
-
Release the LH rear parking brake with
the EPB release tool.
-
Release the connector lock, and then
disconnect the EPB harness electrical connector from the LH rear brake caliper.
-
Remove the bolts (x2) that attach the
LH rear brake caliper to the LH rear knuckle, and then use an S-hook to hang the caliper
on the body.NoteRoute the caliper hose so that it does not get caught on the stabar assembly.Tip: Use of the following tool(s) is recommended:
- 21 mm socket
-
Remove the LH rear brake rotor.
NoteAfter the caliper is released, the rotor is also loose.
-
Remove the bolts (x4) that attach the
LH rear hub to the LH rear knuckle, and then remove the hub from the vehicle.NoteShield will be loose until the hub is installed. There is an insert on the shield for orientation.Tip: Use of the following tool(s) is recommended:
- 18 mm socket
Install
-
Position the LH rear hub assembly to
the LH rear knuckle, and then install the bolts (x4) that attach the hub assembly to the
knuckle..NoteThe shield will be loose until the hub is installed. There is an insert on the shield for orientation.Tip: Use of the following tool(s) is recommended:
- 18 mm socket
-
Mount the LH rear brake rotor.
-
Position the LH rear brake caliper to
the LH rear knuckle, and then install the bolts (x2) that attach the caliper to the
knuckle.NoteWatch for clearance when torquing to not damage the lines or connector.Tip: Use of the following tool(s) is recommended:
- 21 mm socket
-
Position the LH rear wheel speed
sensor onto the knuckle, and then install the bolt and clips (x2) that attach the sensor
to the knuckle.Tip: Use of the following tool(s) is recommended:
- Torx T30 socket
-
Connect the rear left chassis corner
harness electrical connector to the brake caliper, and then engage the connector
lock.
- Install the LH rear wheel. See Wheel Assembly (Remove and Install).
- Install the LH rear wheel center cap. See Wheel Cover - Front - LH (Remove and Install).
- Remove the vehicle from the lift. See Raise Vehicle - 2 Post Lift.
- Raise the LH front window and close the LH front door.