2024-07-23

Bracket - Upper - Center Floor (Remove and Install)

Correction code 1530083041 1530083042 FRT 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Move the LH front seat fully rearward.
  3. Partially the release LH side lower A-pillar primary seal.
  4. Remove the LH mid A-pillar trim. See Trim - A-Pillar - Mid - LH (Remove and Install).
  5. Remove the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Install).
  6. Remove the footwell cover. See Cover - Footwell (Remove and Install).
  7. Remove the LH center floor rail. See Rail - Center Floor - LH (Remove and Install).
  8. Remove the accelerator pedal side trim. See Side Trim - Pedal (Remove and Install).
  9. Remove the accelerator pedal. See Accelerator Pedal (Remove and Install).
  10. Open the RH front door and lower the RH front window.
  11. Move the RH front seat fully rearward.
  12. Partially release the RH front door seal.
  13. Remove the RH mid A-pillar trim. See Trim - A-Pillar - Mid - LH (Remove and Install).
  14. Remove the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Install).
  15. Remove the RH center floor rail. See Rail - Center Floor - LH (Remove and Install).
  16. Fold back the RH carpet.
  17. Remove the center console front panel. See Panel - Front - Center Console (Remove and Install).
  18. Remove the center floor trim. See Trim - Center Floor - Lower (Remove and Install).
  19. Remove the push clips (x2) and release the edge clips (x2) and retaining clips (x2) that attach the center floor upper bracket to the vehicle, and then remove the bracket from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Depress either side of the retaining clip, and then push inward to release the upper bracket from the duct.

Install

  1. Position the center floor upper bracket into the vehicle, and then install the edge clips (x2), retaining clips (x2), and push clips (x2) that attach the bracket to the vehicle.
  2. Install the center floor trim. See Trim - Center Floor - Lower (Remove and Install).
  3. Install the center console front panel. See Panel - Front - Center Console (Remove and Install).
  4. Unfold the RH front cabin carpet into position.
  5. Install the RH center floor rail. See Rail - Center Floor - LH (Remove and Install).
  6. Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Install).
  7. Install the RH mid A-pillar trim. See Trim - A-Pillar - Mid - LH (Remove and Install).
  8. Install the RH front door seal.
  9. Unfold the LH front cabin carpet into position.
  10. Install the accelerator pedal. See Accelerator Pedal (Remove and Install).
  11. Install the accelerator pedal side trim. See Side Trim - Pedal (Remove and Install).
  12. Install the LH center floor rail. See Rail - Center Floor - LH (Remove and Install).
  13. Install the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Install).
  14. Install the LH mid A-pillar trim. See Trim - A-Pillar - Mid - LH (Remove and Install).
  15. Install the LH side lower A-pillar primary seal.
  16. Install the footwell cover. See Cover - Footwell (Remove and Install).
  17. Restore the RH front seat back to its original position.
  18. Raise the RH front window and close the RH front door.
  19. Restore the LH front seat back to its original position.
  20. Raise the LH front window and close the LH front door.