05/01/2024 11:11:03

2nd Row Seat Back Hardware - 2nd Row Seat Shoulder Cover - LH (Remove and Install)

Correction code 1305003011 FRT 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Open the LH rear door and lower the LH rear window.
  3. Remove the front header trim. See Headliner Trim - Front Header Trim (Remove and Install).
  4. Remove the LH mid A-pillar trim. See A-B-C Positivet Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  5. Remove the LH dash panel quarter panel assembly. See Dash Panel - Quarter Panel Assembly - LH (Remove and Install).
  6. Remove the LH upper A-pillar trim. See A-B-C Positivet Interior Trim - A-Pillar Upper Trim - LH (Remove and Install).
  7. Move the LH front seat fully forward.
  8. Remove the rear header trim. See Headliner Trim - Rear Header Trim (Remove and Install).
  9. Remove the LH cantrail trim. See Headliner Trim - Cantrail Trim - LH (Remove and Install).
  10. Remove the LH 2nd row seat side bolster. See 2nd Row Seat Assemblies - 2R Seat Side Bolster LH (Remove and Install).
  11. Partially remove the LH rear primary door seal.
  12. Release the clips (x3), tabs (x7), and datums (x4) that attach the LH lower C-pillar trim to the C-pillar.
    Informational PurposesAn informational icon, calling your attention
    Note
    Starting at the door sill, pull upward, and then forward to release.
    Informational PurposesAn informational icon, calling your attention
    Note
    Leave the trim attached to the seat belt.
  13. Remove the LH C-pillar upper trim. See A-B-C Positivet Interior Trim - C-Pillar Upper Trim - LH (Remove and Install).
  14. Release the clips (x7) and datum that attach the LH 2nd row shoulder cover to the body, and then remove the cover from the vehicle.

Install

  1. Fasten the clips (x7) and datum that attach the LH 2nd row shoulder cover to the body.
  2. Install the LH C-pillar upper trim. See A-B-C Positivet Interior Trim - C-Pillar Upper Trim - LH (Remove and Install).
  3. Secure the clips (x3), tabs (x7), and datums (x4) that attach the LH lower C-pillar trim to the C-pillar.
  4. Secure the LH rear primary door seal.
  5. Install the LH 2nd row seat side bolster. See 2nd Row Seat Assemblies - 2R Seat Side Bolster LH (Remove and Install).
  6. Install the LH cantrail trim. See Headliner Trim - Cantrail Trim - LH (Remove and Install).
  7. Install the rear header trim. See Headliner Trim - Rear Header Trim (Remove and Install).
  8. Install the LH upper A-pillar trim. See A-B-C Positivet Interior Trim - A-Pillar Upper Trim - LH (Remove and Install).
  9. Install the LH dash panel quarter panel assembly. See Dash Panel - Quarter Panel Assembly - LH (Remove and Install).
  10. Install the LH mid A-pillar trim. See A-B-C Positivet Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  11. Install the front header trim. See Headliner Trim - Front Header Trim (Remove and Install).
  12. Raise the LH rear window and close the LH rear door.
  13. Restore the LH front seat back to its original position.
  14. Raise the LH front window and close the LH front door.