23/07/2024 17:25:47

Bed Cargo Tub - Bed Cargo Smugglers Bay (Remove and Install)

Correction code 1215014041 1215014042 FRT 1.32 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the tonneau cover.
  2. Open the tailgate.
  3. Remove the truck bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
  4. Remove the bed cargo tub struts. See Tonneau - Bed Cargo Tub Strut (Remove and Install).
  5. Remove the bed cargo tub lid. See Bed Cargo Tub - Bed Cargo Tub Lid (Remove and Replace).
  6. Remove the LH and RH sail applique assemblies. See Truck Bed Exterior Trim - Sail Applique Assembly - LH (Remove and Replace).
  7. Release the clip that attaches the LH tonneau rail seal to the vehicle, and then pull the seal away from the groove to release it. Repeat this step for the RH side of the vehicle.
  8. Remove the LH and RH upper bed side wall assemblies. See Truck Bed Exterior Trim - Upper Bed Side Wall Assembly - LH (Remove and Install).
  9. Remove the LH and RH rear bed closeouts. See Truck Bed - Rear Bed Closeout - LH (Remove and Install).
  10. Remove the LH and RH bed side walls. See Bed Side Wall - Bed Side Wall - LH (Remove and Install).
  11. Remove the bolts (x4) that attach the bed cargo smugglers bay to the body.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  12. With assistance, remove the bed cargo smugglers bay from the vehicle.

Install

  1. With assistance, install the bed cargo smugglers bay in the vehicle.
  2. Install the bolts (x4) that attach the bed cargo smugglers bay to the body.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Install the LH and RH bed side walls. See Bed Side Wall - Bed Side Wall - LH (Remove and Install).
  4. Install the LH and RH rear bed closeouts. See Truck Bed - Rear Bed Closeout - LH (Remove and Install).
  5. Install the LH and RH upper bed side wall assemblies. See Truck Bed Exterior Trim - Upper Bed Side Wall Assembly - LH (Remove and Install).
  6. Position the LH tonneau rail seal into the vehicle, press the seal into the groove, and then secure the clip that attaches the seal to the vehicle. Repeat this step for the RH tonneau rail seal.
  7. Install the LH and RH sail applique assemblies. See Truck Bed Exterior Trim - Sail Applique Assembly - LH (Remove and Replace).
  8. Install the bed cargo tub lid. See Bed Cargo Tub - Bed Cargo Tub Lid (Remove and Replace).
  9. Install the bed cargo tub struts. See Tonneau - Bed Cargo Tub Strut (Remove and Install).
  10. Install the truck bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
  11. Close the tonneau cover.
  12. Close the tailgate.