30/10/2024 10:53:08

Passenger Compartment Carpet - End Item, Passenger Carpet Assembly, Soft Trim (Remove and Install)

Correction code 1530083081 1530083082 FRT 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-10-30: Added step to remove lower B-pillar trim. Updated step to fold back RH front carpet
  • 2024-08-20: Added steps to check for and install backbone harness guide.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Open the RH front door and lower the RH front window.
  3. Move the RH front seat fully rearward.
  4. Remove the RH lower B-pillar trim. See A-B-C Post Interior Trim - B-Pillar Lower Trim - LH (Remove and Install).
  5. Remove the footwell cover. See Dash Support Frame - Footwell Cover (Remove and Install).
  6. Remove the RH center floor rail. See Passenger Compartment Carpet - Center Floor Rail - LH (Remove and Install).
  7. Release the clips (x8) and datums (x4) that attach the front portion of the RH front carpet to the vehicle, and then fold the carpet back.
  8. Lift the RH carpet support foam from the rear edge, and then remove the support foam from the vehicle.
  9. Remove the RH front seat riser crossmember cover. See Front Seat Sliders and Controllers - 1R Seat Riser Crossmember Cover (Remove and Install).
  10. Remove the fasteners (x3) that attach the RH seat riser crossmember to the vehicle, release the clips (x3) that attach the harness to the crossmember, and then remove the crossmember from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    The 13 mm bolt is threadlocked.
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • 10 mm socket
  11. Remove the RH 1st row seat outboard riser bolt cover.
  12. Remove the front passenger carpet assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    The plastic portions at the rear of the carpet need to clear risers.

Install

  1. Check for the presence of a backbone harness guide:
    • If the harness guide is present, skip to step 9.
    • If the harness guide is not present, continue to the next step.
  2. Remove any remaining tape from the casting and backbone harness.
  3. Remove and discard the front casting clip.
  4. Install the backbone harness guide onto the front casting.
  5. Position the backbone harness so that it lays flat on the harness guide, and then mark the positions at the front and rear edges of the harness guide on the harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push the backbone harness flat starting at lower edge. Make alignment marks from the backbone harness to the guide at the bottom then the top while pushing the backbone harness flat.
  6. Remove the backbone harness guide from the casting once marked.
  7. Starting from the lower edge of the harness guide, install the backbone harness onto the harness guide using the alignment marks made in the previous steps, and then use electrical tape to secure the harness to the guide.
    Informational PurposesAn informational icon, calling your attention
    Note
    Refer to the image for electrical tape positions (x3).
    Figure 1. Electrical tape positions
  8. Secure the backbone harness and harness guide to the front casting.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the rib groove is aligned and engaged correctly. Lower engagement will make an audible click when secured.
  9. Install the front passenger carpet assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    The plastic portions at the rear of the carpet need to clear risers.
  10. Install the RH 1st row seat outboard riser bolt cover.
  11. Position the RH seat riser crossmember into the vehicle, secure the clips (x3) that attach the harness to the crossmember, and then install the fasteners (x3) that attach the crossmember to the vehicle.
    35 Nm (25.8 lbs-ft)
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The 13 mm bolt is torqued to 35 Nm, and the 10 mm bolts (x2) to 9 Nm.
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • 10 mm socket
  12. Install the RH front seat riser crossmember cover. See Front Seat Sliders and Controllers - 1R Seat Riser Crossmember Cover (Remove and Install).
  13. Install the RH carpet support foam.
    Informational PurposesAn informational icon, calling your attention
    Note
    Seat the foam at the rear edge.
  14. Unfold the RH front cabin carpet into position, and then secure the clips (x8) and datums (x4).
  15. Install the RH center floor rail. See Passenger Compartment Carpet - Center Floor Rail - LH (Remove and Install).
  16. Install the footwell cover. See Dash Support Frame - Footwell Cover (Remove and Install).
  17. Install the RH lower B-pillar trim. See A-B-C Post Interior Trim - B-Pillar Lower Trim - LH (Remove and Install).
  18. Restore the RH front seat back to its original position.
  19. Raise the RH front window and close the RH front door.
  20. Raise the LH rear window and close the LH rear door.