2024-12-11

Door Glass - Moving Glass - Front LH (Remove and Install)

Correction code 1020030101 FRT 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-12-11: Added new caution about Pre-Installation Glass Inspection service requirements.
  • 2024-10-17: Update glass to regulator torque to 4 Nm.
  • 2024-05-13: Added step and warning to support glass while removing regulator fasteners.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
New glass components (windshield, roof, door, and fixed glass) must be inspected before installation to meet Tesla’s internal standards of quality. Perform the inspection described in Pre-Installation Glass Inspection before beginning this procedure.

Remove

  1. Remove the LH front door trim panel. See Front Door Trim Pad - Door Trim Front - LH (Remove and Install).
  2. Connect an external window switch.
  3. Use a pocket screwdriver to manually latch the LH front door.
  4. Raise the LH front window.
  5. Release the rubber datums (x6) to remove the LH front door inner waist belt seal from the door assembly.
  6. Remove the LH front door grommets (x4).
  7. With the help of an assistant, hold the door glass in position before continuing to the next step.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The clamps do not hold the entire regulator base. Failure to support the glass while removing the fasteners in the next step may result in the glass slipping off the regulator.
  8. With the assistant supporting the glass, remove the bolts (x2) that attach the LH front door moving glass to the regulator, and then remove the glass from the door.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Make sure to support the glass while removing the fasteners. The clamps do not hold the entire base of the regulator.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket

Install

  1. Position the LH front door moving glass into the LH front door, and then install and hand tighten the bolts (x2) that attach the glass from the regulator.
    Informational PurposesAn informational icon, calling your attention
    Note
    Be careful of the glass slipping off of the mount.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  2. Manually release the LH front door latch.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the manual release cable away from the vehicle to unlatch.
  3. Close the LH front door.
  4. Check and adjust the gap and flushness of the LH front door moving glass.
    Informational PurposesAn informational icon, calling your attention
    Note
    Connect a external window switch to help with adjustment if needed.
  5. Open the LH front door.
  6. Torque the bolts (x2) that attach the LH front door moving glass to the regulator, and then install the grommets (x2).
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  7. Install the LH front door inner waist belt seal.
  8. Install the LH front door trim panel. See Front Door Trim Pad - Door Trim Front - LH (Remove and Install).
  9. Calibrate the LH front window.
    Informational PurposesAn informational icon, calling your attention
    Note
    Press and hold down the selected window for 15 seconds. Raise the window and hold for 15 seconds. Test window by hard pressing to verify auto raise/lower functions correctly.
  10. Raise the LH front window and close the LH front door.