23/07/2024 17:24:58

Air Suspension Compressor and Reservoir - Air Suspension Valve Block (Remove and Replace)

Correction code NA NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Cybertruck electronics are powered by a 48V "mid voltage" or "MV" architecture that is designed to improve efficiency. Servicing MV components requires extra knowledge and care in order to avoid personal and/or vehicular harm. Read and understand MV precautions in Electrical Precautions and make sure any required MV-related training courses have been completed, as applicable.

Remove

  1. Raise and support the vehicle. See Raise Vehicle - 2 Post Lift.
  2. Open the LH front door and lower the LH front window.
  3. Place the vehicle into Service Mode. See Service Mode.
  4. Unlock the vehicle Gateway. See Gateway (Unlock).
  5. On the vehicle touchscreen, navigate to Service > Chassis > Suspension > Service > Deflate All, and then touch Run to deflate the TAS system.
  6. Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  7. Open the tonneau cover.
  8. Open the tailgate.
  9. Disconnect MV power. See Disconnect MV Power.
  10. Remove the bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
  11. Disconnect the air suspension valve block electrical connector.
  12. Disconnect the air lines (x5) from the air suspension valve block.
    Tip: Use of the following tool(s) is recommended:
    • 14 mm combination wrench
    • 12 mm combination wrench
  13. Remove and discard the used collet and VOSS connector from the air lines.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replacement fittings will come installed on new the valve block.
  14. Rotate the air suspension valve block assembly clockwise to release the grommets (x2) at the top of the assembly, and then pull the valve block upwards at a 45 degree angle to release the grommet at the bottom of the assembly.

Install

  1. Position the new air suspension valve block into the bracket, rotate the valve block counter-clockwise until the top grommets (x2) are secured into the bracket, and then push the valve block downwards at a 45 degree angle to secure the bottom grommet into the groove.
  2. Remove the shipping plugs from the air line fittings, and then install the air lines (x5) into the air suspension valve block.
    Informational PurposesAn informational icon, calling your attention
    Note
    Match the corresponding colors on the air line and valve block.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push the air line into the fitting until the depth mark is flush.
    Informational PurposesAn informational icon, calling your attention
    Note
    Perform a push-pull-push test to verify the lines are fully installed.
    Informational PurposesAn informational icon, calling your attention
    Note
    New VOSS fittings should come preinstalled in the valve block.
  3. Connect the air suspension valve block electrical connector.
  4. Install the bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
  5. Reconnect MV power. See Disconnect MV Power.
  6. Install the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  7. Close the tonneau cover.
  8. Close the tailgate.
  9. Refill the air suspension reservoir. See Air Suspension - Pressurize / Depressurize - Full System.