26/11/2024 16:01:27

Mud Flaps (Retrofit)

Correction code 12207006 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Retrofit

  1. Open the LH front door and lower the LH front window.
  2. Turn the steering wheel fully to the left to provide access to the working areas.
  3. Remove the clips (x2) that partially attach the LH front wheel arch liner to the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
    Figure 1. LH shown; RH similar
  4. Position the LH front mud flap on the vehicle, and then install the clips (x2) that attach the mud flap to the LH front wheel arch liner.
    Informational PurposesAn informational icon, calling your attention
    Note
    Install the clips starting from right to left.
    Figure 2. LH shown; RH similar
    Figure 3. LH shown; RH similar
  5. Install the bolts (x2) that attach the LH front mud flap to the LH rocker panel.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Align the bolts with the rocker panel holes.
    Tip: Use of the following tool(s) is recommended:
    • 2 in extension
    • 10 mm deep socket
    • Cordless Ratchet/Impact Driver
    • Torque wrench with angle measurement
    Figure 4. LH shown; RH similar
  6. Remove the clips (x3) that partially attach the RH rear wheel arch liner to the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
    Figure 5. RH shown; LH similar
  7. Remove the bolt that partially attaches the RH rear diffuser to the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 2 in extension
    • Cordless Ratchet/Impact Driver
    • Torx T30 socket
    Figure 6. RH shown; LH similar
  8. Move the RH rear wheel arch liner away from the working area as required, and then install the U-nuts (x3) onto the RH rear fascia.
    Figure 7. RH shown; LH similar
  9. Move the RH rear wheel arch liner back to original position.
    Figure 8. RH shown; LH similar
  10. Position the RH rear mud flap on the vehicle, and then install the bolts (x3) that attach the mud flap to the RH rear wheel arch liner.
    2.2 Nm (1.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Cordless Ratchet/Impact Driver
    • Torque wrench with angle measurement
    Figure 9. RH shown; LH similar
    Figure 10. RH shown; LH similar
  11. Install the bolt that attaches the RH rear mud flap to the RH rear diffuser.
    2.2 Nm (1.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Cordless Ratchet/Impact Driver
    • Torque wrench with angle measurement
    Figure 11. RH shown; LH similar
  12. Turn the steering wheel fully to the right to provide access to the working areas.
  13. Repeat step 3 through step 5 for the RH front mud flap.
  14. Repeat step 6 through step 11 for the LH rear mud flap.
  15. Raise the LH front window and close the LH front door.