23/07/2024 17:23:30

2nd Row Seat Back Hardware - 2R Seat Underbelly LH (Remove and Install)

Correction code 1305003061 1305003062 FRT 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Open the LH rear door and lower the LH rear window.
  3. Remove the 2nd row floor mat.
  4. Remove the front header trim. See Headliner Trim - Front Header Trim (Remove and Install).
  5. Remove the LH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  6. Remove the LH upper A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Upper Trim - LH (Remove and Install).
  7. Move the LH front seat fully forward.
  8. Remove the rear header trim. See Headliner Trim - Rear Header Trim (Remove and Install).
  9. Remove the LH cantrail trim. See Headliner Trim - Cantrail Trim - LH (Remove and Install).
  10. Remove the LH 2nd row outboard bolster. See 2nd Row Seat Assemblies - 2R Seat Side Bolster LH (Remove and Install).
  11. Partially release the LH rear primary door seal.
  12. Remove the LH lower C-pillar trim. See A-B-C Post Interior Trim - C-Pillar Lower Trim - LH (Remove and Install).
  13. Remove the LH upper C-pillar trim. See A-B-C Post Interior Trim - C-Pillar Upper Trim - LH (Remove and Install).
  14. Fold the LH and RH 2nd row seats cushions up.
  15. Release the clip and datum that attach the front portion of the RH lower C-pillar trim.
  16. Remove the rear wall lower trim. See Passenger Compartment Carpet - End Item, Rear Wall Lower Trim, Soft Trim (Remove and Install).
  17. Fold the RH 2nd row seat cushion down.
  18. Disconnect the LH 2nd row cushion assembly electrical connectors (x3), and then release the harness clips (x5).
  19. Release the clip that attaches the LH 2nd row seat cushion outboard cover to the seat assembly, and then pull the cover outward from the front lower section to release it from the assembly.
  20. Release the LH 2nd row cushion from the underbelly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the plastic retainers outward to release the underbelly from the cushion.
  21. Pull the bottom of the LH 2nd row seat underbelly outwards to release the clips (x8), and then remove the underbelly from the seat assembly.

Install

  1. Position the LH 2nd row seat underbelly onto the seat assembly, and then push the underbelly inwards to engage the clips (x8) that attach the underbelly to the seat assembly.
  2. Secure the LH 2nd row cushion to the underbelly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the plastic retainers into the channel.
  3. Position the LH 2nd row seat cushion outboard cover to the seat assembly, and then secure the clip that attaches the cover to the assembly.
  4. Connect the LH 2nd row cushion assembly electrical connectors (x3), and then secure the harness clips (x5).
  5. Install the rear wall lower trim. See Passenger Compartment Carpet - End Item, Rear Wall Lower Trim, Soft Trim (Remove and Install).
  6. Fold the LH 2nd row seat cushion down.
  7. Install the LH upper C-pillar trim. See A-B-C Post Interior Trim - C-Pillar Upper Trim - LH (Remove and Install).
  8. Install the LH lower C-pillar trim. See A-B-C Post Interior Trim - C-Pillar Lower Trim - LH (Remove and Install).
  9. Secure the LH rear primary door seal.
  10. Install the LH 2nd row outboard bolster. See 2nd Row Seat Assemblies - 2R Seat Side Bolster LH (Remove and Install).
  11. Install the LH cantrail trim. See Headliner Trim - Cantrail Trim - LH (Remove and Install).
  12. Install the rear header trim. See Headliner Trim - Rear Header Trim (Remove and Install).
  13. Install the LH upper A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Upper Trim - LH (Remove and Install).
  14. Install the LH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  15. Install the front header trim. See Headliner Trim - Front Header Trim (Remove and Install).
  16. Raise the LH rear window and close the LH rear door.
  17. Install the clip and datum that attach the RH lower C-pillar trim to the vehicle.
  18. Install the 2nd row floor mat.
  19. Raise the RH rear window and close the RH rear door.
  20. Restore the LH front seat back to its original position.
  21. Raise the LH front window and close the LH front door.