23/07/2024 17:29:11

Front Bumper Carrier - Front End Carrier Plastic Assembly (Remove and Install)

Correction code 1001045011 1001045012 FRT 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Remove the LH and RH headlamp assemblies. See Headlamps - Headlamp Assembly - LH (Remove and Install).
  2. Remove the bolts (x2) that attach the hood latch to the front end carrier, and then remove the hood latch from the front end carrier.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Remove the bolts (x3) that attach the latch actuator to the front end carrier, and then remove the actuator from the front end carrier.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  4. Release the clips (x2) that attach the harness to the front end carrier.
  5. Remove the bolts (x8) that attach the front end carrier to the vehicle, and then remove the front end carrier from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Clear the datums (x4) to remove the carrier from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • 13 mm socket

Install

  1. Position the front end carrier into the vehicle, and then install the bolts (x8) that attach the front end carrier to the vehicle.
    5 Nm (3.7 lbs-ft)
    30 Nm (22.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Position the carrier and align using the datums (x4).
    Informational PurposesAn informational icon, calling your attention
    Note
    The 10 mm bolts (x6) are torqued to 5 Nm, and the 13 mm bolts (x2) are torqued to 30 Nm.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • 13 mm socket
  2. Install the clips (x2) that attach the harness to the front end carrier.
  3. Position the latch actuator to the front end carrier, and then install the bolts (x3) that attach the actuator to the front end carrier.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  4. Position the hood latch to the front end carrier, and then install the bolts (x2) that attach the hood latch to the front end carrier.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Align the hood latch with the bolt marks.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Install the LH and RH headlamp assemblies. See Headlamps - Headlamp Assembly - LH (Remove and Install).