23/07/2024 17:33:51

Rocker Panel Trim - Rocker Assembly - LH (Remove and Install)

Correction code 1220105011 FRT 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Release the clips (x11) that attach the rear of the LH fender flare cover to the vehicle, and then disconnect the electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the fender flare as needed for clearance. Full removal is not required.
  2. Remove the bolt that attaches the front of the LH rocker to the step reinforcement.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Remove the clip that attaches the LH rocker cover to the LH front wheel liner.
  4. Release the clips (x13) that attach the front of the LH rear fender flare cover to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release as needed for clearance. Full removal is not required.
  5. Remove the bolt that attaches the rear of the LH rocker to the step reinforcement.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  6. Remove the clip that attaches the LH rocker cover to the LH rear wheel liner.
  7. Remove the bolts (x6) that attach the LH rocker assembly to the LH side ski.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  8. Release the clips (x11) that attach the LH rocker assembly to the rocker carrier, and then remove the rocker assembly from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove any clips that remained in the carrier.

Install

  1. Position the LH rocker assembly to the rocker carrier, and then secure the clips (x11) that attach the rocker assembly to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace any missing or damaged clips.
  2. Install the bolts (x6) that attach the LH rocker assembly to the LH side ski.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Install the clip that attaches the LH rocker cover to the LH rear wheel liner.
  4. Install the bolt that attaches the rear of the LH rocker to the step reinforcement.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Secure the clips that attach the front of the LH rear fender flare cover to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace any missing or damaged clips.
  6. Install the clip that attaches the LH rocker cover to the LH front wheel liner.
  7. Install the bolt that attaches the front of the LH rocker to the step reinforcement.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  8. Connect the electrical connector, and then secure the clips that attach the rear of the LH fender flare cover to the vehicle.