23/07/2024 17:35:25

Truck Bed - False Wall Assembly (Remove and Install)

Correction code 1215125061 1215125062 FRT 1.02 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the tonneau cover.
  2. Open the tailgate.
  3. Remove the truck bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
  4. Remove the bed cargo tub struts. See Tonneau - Bed Cargo Tub Strut (Remove and Install).
  5. Remove the bolts (x4) that attach the bed cargo tub lid.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance.
  6. Remove the LH and RH sail applique assemblies. See Truck Bed Exterior Trim - Sail Applique Assembly - LH (Remove and Replace).
  7. Remove the LH tonneau rail seal. Repeat this step for the RH tonneau rail seal.
    Informational PurposesAn informational icon, calling your attention
    Note
    x1 clip
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull away from the rail to release from groove.
  8. Remove the LH and RH upper bed side wall assemblies. See Truck Bed Exterior Trim - Upper Bed Side Wall Assembly - LH (Remove and Install).
  9. Remove the LH and RH rear bed closeouts. See Truck Bed - Rear Bed Closeout - LH (Remove and Install).
  10. Remove the LH and RH bed side walls. See Bed Side Wall - Bed Side Wall - LH (Remove and Install).
  11. Remove the bolts (x2) that attach the false wall assembly to the body, and then remove the false wall assembly from the vehicle.
    45 Nm (33.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommended to use assistance to prevent scratching the bed liner.

Install

  1. Install the bolts (x2) that attach the false wall assembly to the body.
    45 Nm (33.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommended to use assistance to prevent scratching the bed liner.
  2. Install the LH and RH bed side walls. See Bed Side Wall - Bed Side Wall - LH (Remove and Install).
  3. Install the LH and RH rear bed closeouts. See Truck Bed - Rear Bed Closeout - LH (Remove and Install).
  4. Install the LH and RH upper bed side wall assemblies. See Truck Bed Exterior Trim - Upper Bed Side Wall Assembly - LH (Remove and Install).
  5. Install the LH tonneau rail seal. Repeat this step for the RH tonneau rail seal.
    Informational PurposesAn informational icon, calling your attention
    Note
    x1 clip
  6. Install the LH and RH sail applique assemblies. See Truck Bed Exterior Trim - Sail Applique Assembly - LH (Remove and Replace).
  7. Install the bolts (x4) that attach the bed cargo tub lid.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance.
    Informational PurposesAn informational icon, calling your attention
    Note
    Position the bed cargo tub lid onto the vehicle. Install the bolts that attach the bed cargo tub lid onto the hinges.
  8. Install the bed cargo tub struts. See Tonneau - Bed Cargo Tub Strut (Remove and Install).
  9. Install the truck bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
  10. Close the tonneau cover.
  11. Close the tailgate.