20/08/2024 15:15:21

Passenger Compartment Carpet - End Item, Rear Carpet Assembly, Soft Trim (Remove and Install)

Correction code 1530083091 1530083092 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-08-20: Added step to check backbone harness alignment and install anti-abrasion tape if missing.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open all the doors and lower all the windows.
  2. Remove the LH and RH A-pillar mid trims. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  3. Remove the LH and RH A-pillar lower trims. See A-B-C Post Interior Trim - A-Pillar Lower Trim - LH (Remove and Install).
  4. Move the LH and RH front seats fully forward.
  5. Fold up the 2nd row 40 seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the tether to release the seat cushion, and then lift up the cushion until locked in place.
  6. Fold up the 2nd row 60 seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the tether to release the seat cushion, and then lift up the cushion until locked in place.
  7. Remove the 2nd row floor mat.
  8. Partially release the LH lower C-pillar trim. Repeat this step for the RH lower C-pillar trim.
    Informational PurposesAn informational icon, calling your attention
    Note
    x1 clip, x1 datum
  9. Remove the rear wall lower trim. See Passenger Compartment Carpet - End Item, Rear Wall Lower Trim, Soft Trim (Remove and Install).
  10. Remove the LH and RH lower B-pillar trims. See A-B-C Post Interior Trim - B-Pillar Lower Trim - LH (Remove and Install).
  11. Release the clips (x4) that attach the RH duct bezel to the rear carpet. Repeat this step for the LH duct bezel.
    Figure 1. LH side shown, RH similar
    Figure 2. LH side shown, RH similar
    Figure 3. LH side shown, RH similar
  12. Release the HV cabin outlets harness from the foam.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide outwards out of the groove.
  13. Remove the rear carpet assembly from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    x4 clips, x17 stands, x6 datums
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the stands around the LH and RH floor ducts, and then release the stands at the center console. Fold back the carpet and stands from the forward edge. Fold the rear carpet and foam forward, and then pull the center of carpet and foam upward to remove the carpet from the vehicle. Remove any clips, if they remain on the HV battery side.

Install

  1. Inspect the backbone harness for any misalignment at the rear ribs and apply anti-abrasion tape if missing.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the cable lays flat and is not twisted.
    Informational PurposesAn informational icon, calling your attention
    Note
    Apply surface protection at the seam of the rearmost rib under backbone cable if missing. Use black anti-abrasion tape (PN: 1879451-99-A) if available. If black anti-abrasion tape is available, remove the red 3M VHB tape, and then apply the black anti-abrasion tape. If black anti-abrasion tape is not available, apply the red 3M VHB tape (PN: 1879451-00-B) over exposed seams.
  2. Install the rear carpet assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    x4 clips, x6 datums
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the center foams and datums. Secure the stands at the center console, and then secure stands around the LH and RH floor ducts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Fully tuck the carpet under the risers and trim.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace any missing or damaged clips.
  3. Secure the HV cabin outlets harness to foam.
    Informational PurposesAn informational icon, calling your attention
    Note
    Tuck the harness into the groove.
  4. Install the LH duct bezel to the rear carpet. Repeat this step for the RH duct bezel.
    Informational PurposesAn informational icon, calling your attention
    Note
    x4 clips
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace any missing or damaged clips.
  5. Install the LH and RH lower B-pillar trims. See A-B-C Post Interior Trim - B-Pillar Lower Trim - LH (Remove and Install).
  6. Install the rear wall lower trim. See Passenger Compartment Carpet - End Item, Rear Wall Lower Trim, Soft Trim (Remove and Install).
  7. Install the 2nd row floor mat.
  8. Secure the LH and RH lower C-pillar trims.
    Informational PurposesAn informational icon, calling your attention
    Note
    x1 clip, x1 datum
    Figure 4. LH side
    Figure 5. RH side
  9. Fold down the 2nd row 40 seat. Repeat this step for the 2nd row 60 seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the tether to release the seat cushion, and then pivot down the cushion until locked in place.
    Figure 6. 2nd row 40 seat shown, 2nd row 60 seat similar
    Figure 7. 2nd row 40 seat shown, 2nd row 60 seat similar
  10. Install the LH and RH A-pillar lower trims. See A-B-C Post Interior Trim - A-Pillar Lower Trim - LH (Remove and Install).
  11. Install the LH and RH A-pillar mid trims. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  12. Restore the LH and RH front seats back to their original position.
  13. Raise all the windows and close all the doors.