23/07/2024 17:30:14

Front Seat Covers and Pads - 1R FSC Trim 1R LH/RH (Remove and Install)

Correction code 1307060051 1307060052 FRT 0.90 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-04-09: Cleaned up topic.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Remove the LH 1st row seat assembly. See Front Seat Assemblies - 1st Row Seat Assembly - LH Drive - LH - Black (Remove and Install).
  2. Remove the LH outboard side shield. See Front Seat Covers and Pads - 1R LH Outboard Cybershield Fab (Remove and Install).
  3. Remove the bolt, and then release the clips (x2) and tabs (x2) that attach the 1st row LH outboard side shield carrier to the seat. Release the leading edge of the trim and slide away from the seat frame.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 bit
  4. Remove the LH front seat inboard cover. See Front Seat Covers and Pads - 1R LH Inboard Cybershield Paint (Remove and Install).
  5. Remove the LH front seat buckle. See 1st Row Seat Belts - ZF First Row Buckle - Sumitomo (Remove and Install).
  6. Release the clips (x2) that attach the 1st row LH inboard side shield carrier to the seat frame. Release the leading edge of trim, and then slide away from the seat frame.
  7. Put the seat on a protected surface such as a 500 lb portable bench or similar.
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance.
    Informational PurposesAn informational icon, calling your attention
    Note
    Put the seat so that the underside of the seat can be accessed.
  8. Release the seat back elastic straps (x2) from the seat frame.
    Tip: Use of the following tool(s) is recommended:
    • Pick Miniature Soft Grip, 90 degree tip, 6 in
  9. Release the soft trim retainers (x2) from the seat frame.
  10. Release the soft trim retainer from the inboard side of the seat frame.
  11. Release the soft trim retainer from the outboard side of the seat frame.
  12. Release the soft trim retainer from the front end of the seat frame.
  13. Put the seat in the upright position.
  14. Remove the seat cushion from the seat frame.
  15. Cut the hog rings (x3), then release the velcro strips (x3) and strap, and then remove the LH 1st row seat cushion trim. Pass the electrical harness through the trim opening.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Avoid tearing the velcro from the foam.
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove any debris.

Install

  1. Install the LH 1st row seat cushion trim. Secure the trim with velcro strips (x3) and new hog rings (x3). Pass the electrical harness through the trim opening.
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the velcro in indicated locations.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the trim around the foam, and then smooth out the material.
  2. Install the seat bottom cushion onto the seat frame. Feed the trim between the seat back trim and the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Maneuver the seat assembly as needed for access.
  3. Install the soft trim retainer from the outboard side of the seat frame.
  4. Install the soft trim retainer from the inboard side of the seat frame.
  5. Secure the front soft trim retainer to the seat frame.
  6. Rotate the seat assembly onto the seat back.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Protect the seat from damage.
  7. Install the soft trim retainers (x2) onto the seat frame.
  8. Install the seat back elastic straps (x2) onto the seat frame.
  9. Install the 1st row LH inboard side shield carrier and secure the clips (x2) and tabs (x2). Position the leading edge of the trim, and then slide into the seat frame.
  10. Install the LH front seat inboard cover. See Front Seat Covers and Pads - 1R LH Inboard Cybershield Paint (Remove and Install).
  11. Install the LH front seat buckle. See 1st Row Seat Belts - ZF First Row Buckle - Sumitomo (Remove and Install).
  12. Install the LH side shield carrier onto the seat frame and secure the clips (x2) and tabs (x2). Slide the carrier forward onto the seat frame aligning the clips and the tabs.
  13. Install the LH outboard side shield. See Front Seat Covers and Pads - 1R LH Outboard Cybershield Fab (Remove and Install).
  14. Install the LH 1st row seat assembly. See Front Seat Assemblies - 1st Row Seat Assembly - LH Drive - LH - Black (Remove and Install).
  15. Calibrate the LH front seat using the vehicle touchscreen.
    Informational PurposesAn informational icon, calling your attention
    Note
    Touch Controls > Service > Drivers Seat, Steering & Mirrors Calibration > Start. Follow the on screen instructions. Allow the process to complete.
  16. Raise the LH front window and close the LH front door.