23/07/2024 17:32:48

Rear Brake Rotors - Calipers and Pads - Rear Brake Pad Kit (Remove and Install)

Correction code 3301088081 3301088082 FRT 0.71 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning

This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Open LH front door

Note
Push LH B-pillar door trigger to release
Lower LH front window
Raise and support vehicle

Note
Set air suspension to "Jack Mode"
Connect to vehicle using Toolbox 3.0

Note
Vehicle OBD II connection is integrated into drivers lower IP cover, Open Toolbox 3 website and establish connection to the vehicle, https://toolbox.teslamotors.com, Select connection status icon at top right corner, and select connect locally (icon will turn green when vehicle is connected)
Select "Actions" and search for "EPB"
Select PROC_EPBL_START-SERVICE-MODEvia Toolbox: (link), click 'Run', and allow routine to complete

Note
Chock wheel if necessary, Select ‘X’ at top right of window to close once complete
Select ‘PROC_EPBR_START-SERVICE-MODEvia Toolbox: (link)’, click ‘Run’, and allow routine to complete

Note
Hold down brake pedal while performing routine, Caution vehicle may roll freely, Select 'X' at top right of window to close once complete
Disconnect Toolbox 3 from vehicle and remove laptop
Open powered front trunk

Note
Via exterior switch or UI
Remove rear underhood apron

Note
9x clips
Place shop rags underneath brake fluid reservoir
Clean area around brake fluid reservoir and remove brake reservoir cap
Remove LH rear wheel cap

Note
1x cap, 8x clips, Use both hands to firmly pull wheel cap to release clips, Cap may remove with or without mounting ring attached
Remove RH rear wheel cap

Note
1x cap, 8x clips, Use both hands to firmly pull wheel cap to release clips, Cap may remove with or without mounting ring attached
Loosen RH rear wheel nuts

Note
6x nuts, 21mm, 205 Nm
Loosen LH rear wheel nuts

Note
6x nuts, 21mm, 205 Nm
Raise vehicle fully

Note
Set to a comfortable working height, Lower to locks, Ensure locks engage on both sides to prevent tilting
Remove RH rear wheel

Note
6x nuts, 21mm, 205 Nm
Remove LH rear wheel

Note
6x nuts, 21mm, 205 Nm
Disconnect EPB harness connector from LH rear brake caliper

Note
1x connector, Release locking tab
Release LH rear brake line from upper control arm

Note
1x bolt, 10mm, 10 Nm
Remove bolt securing LH rear caliper to bracket

Note
1x bolt, 14mm, 40 Nm
Rotate LH rear caliper upward
Remove LH rear caliper pad return springs

Note
2x springs, Hold pads first then remove springs, Remove one at a time
Remove brake pads from LH rear caliper bracket

Note
2x pads
Placeholder - Compress LH rear brake caliper piston

Note
1x piston, Picture for reference only
Clean LH rear brake caliper and brake pad guide surfaces

Note
Use nylon brush and brake cleaner as needed, Allow 1 minute dry time, Clean both sides of guides
Apply an even layer of Silaramic lubricant to LH rear brake pad contact points and pad guides

Note
2x pads, 4x guides
Install brake pads onto LH rear caliper bracket

Note
2x pads, Ensure pads seat correctly onto guides
Install LH rear caliper pad return springs

Note
2x springs, Hold pads first then install springs, Install one at a time
Rotate LH rear caliper downward

Note
Hold pads to ensure correct fitment
Install bolt securing LH rear caliper to bracket

Note
1x bolt, 14mm, 40 Nm
Install LH rear brake line onto upper control arm

Note
1x bolt, 10 mm, 10 Nm
Connect LH rear EPB harness

Note
1x connector, Engage locking tab
Disconnect RH rear EPB harness

Note
1x connector, Release locking tab
Release RH rear brake line from upper control arm

Note
1x bolt, 10mm, 10 Nm
Remove bolt securing RH rear caliper to bracket

Note
1x bolt, 14mm, 40 Nm
Rotate RH rear caliper upward
Remove RH rear caliper pad return springs

Note
2x springs, Hold pads first then remove springs, Remove one at a time
Remove brake pads from RH rear caliper bracket

Note
2x pads
Placeholder - Compress RH rear brake caliper piston

Note
1x piston, Picture for reference only
Clean RH rear brake caliper and brake pad guide surfaces

Note
Use nylon brush and brake cleaner as needed, Allow 1 minute dry time, Clean both sides of guides
Apply an even layer of Silaramic lubricant to RH rear brake pad contact points and pad guides

Note
2x pads, 4x guides
Install brake pads onto RH rear caliper bracket

Note
2x pads, Ensure pads seat correctly onto guides
Install RH rear caliper pad return springs

Note
2x springs, Hold pads first then install springs, Install one at a time
Rotate RH rear caliper downward

Note
Hold pads to ensure correct fitment
Install bolt securing RH rear caliper to bracket

Note
1x bolt, 14mm, 40 Nm
Install RH rear brake line onto upper control arm

Note
1x bolt, 10 mm, 10 Nm
Connect RH rear EPB harness

Note
1x connector, Engage locking tab
Lower vehicle to access frunk area

Note
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Keep front suspension components free of contacting ground and surrounding items
Check brake fluid level and top off reservoir if necessary

Note
If level is above Max line, remove extra fluid
Install brake reservoir cap
Pump brake pedal a few times to ensure pedal feels normal
Remove shop rags from underneath brake fluid reservoir
Install RH rear wheel

Note
6x nuts, 21mm, 205 Nm
Install LH rear wheel

Note
6x nuts, 21mm, 205 Nm
Lower vehicle until tires are touching the ground

Note
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
Torque LH rear wheel nuts

Note
6x nuts, 21mm, 205 Nm
Torque RH rear wheel nuts

Note
6x nuts, 21mm, 205 Nm
Install RH rear wheel cap

Note
1x cap, 8x clips, Partially secure wheel cap to wheel, While partially installed wheel cover can be rotated to align with tire design, When aligned press inward from center of cap then secure all clips to mounting ring
Install LH rear wheel cap

Note
1x cap, 8x clips, Partially secure wheel cap to wheel, While partially installed wheel cover can be rotated to align with tire design, When aligned press inward from center of cap then secure all clips to mounting ring
Install rear underhood apron

Note
9x clips, Adjust windshield seal as required
Close powered front trunk

Note
Via exterior switch or UI
Remove vehicle from lift

Note
Lower rack arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"
Exit Service Mode

Note
Via UI > Service > Exit, Press and hold "Exit Service Mode" button
Raise LH front window
Close LH front door
Perform a road test and burnish brakes

Note
Ensure proper brake pedal feel and performance Add correction code 00040100 as needed

Cybertruck Service Manual

Rear Brake Rotors - Calipers and Pads - Rear Brake Pad Kit (Remove and Install)

Figure 1

Figure 2

Figure 3