23/07/2024 17:23:24

2nd Row Seat Back Hardware - 2R Seat Armrest Mounting Bracket (Remove and Install)

Correction code 1305003121 1305003122 FRT 1.08 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Remove the armrest closeout. See 2nd Row Seat Back Hardware - 2R Seat Armrest Closeout (Remove and Install).
  2. Remove the bolts (x2) and release the harness clips (x2) that attach the 2nd row armrest assembly to the vehicle, and then remove the assembly from the seat frame.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove the bolts, and then lay the armrest down to access the harness clips.
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
  3. Remove the bolts (x2) and release the clips (x2) and cable stay that attach the armrest latch to the armrest assembly, and then remove the latch from the assembly.
    17 Nm (12.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Actuate the latch as needed with the pull tether to release.
    Tip: Use of the following tool(s) is recommended:
    • 6 mm hex
  4. Remove the fasteners (x4) that attach the mounting bracket to the 2nd row armrest, and then remove the bracket from the armrest.
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove the RH T50 bolt, and then align the 8mm hex bolt with the rounded opening in bracket to remove.
    Tip: Use of the following tool(s) is recommended:
    • Torx T50 socket
    • 8 mm hex
    • 13 mm socket

Install

  1. Position the mounting bracket onto the 2nd row armrest, and then install the fasteners (x4) that attach the bracket to the armrest.
    25 Nm (18.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Install the 8 mm hex bolt aligned with the rounded opening on the bracket, and then install the RH T50 bolt.
    Informational PurposesAn informational icon, calling your attention
    Note
    All the fasteners are torqued to 25 Nm.
    Tip: Use of the following tool(s) is recommended:
    • Torx T50 socket
    • 8 mm hex
    • 13 mm socket
  2. Position the armrest latch to the armrest assembly, and then install the bolts (x2) and secure the clips (x2) and cable stay that attach the latch to the assembly.
    17 Nm (12.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Actuate the latch as needed with the pull tether to engage.
    Tip: Use of the following tool(s) is recommended:
    • 6 mm hex
  3. Position the 2nd row armrest assembly into the vehicle, and then install the bolts (x2) and harness clips (x2) that attach the assembly to the seat frame.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the harness clips, and then pivot the armrest upwards into position before installing bolts.
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
  4. Install the armrest closeout. See 2nd Row Seat Back Hardware - 2R Seat Armrest Closeout (Remove and Install).