23/07/2024 17:30:16

Front Seat Covers and Pads - 1R LH Outboard Cybershield Fab (Remove and Install)

Correction code 1307060091 1307060092 1307060081 1307060082 FRT 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Move the LH front seat fully forward.
  3. Use a flathead screwdriver to rotate the lock mechanism on the front seat belt linkage counterclockwise to release it from the pretensioner, and then slide the linkage off the pretensioner and set it aside.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT rotate clockwise to avoid damage to the mechanism.
    Informational PurposesAn informational icon, calling your attention
    Note
    The linkage design may vary, but will function the same.
    Informational PurposesAn informational icon, calling your attention
    Note
    The lock screw will remain in the horizontal position when released.
    Informational PurposesAn informational icon, calling your attention
    Note
    A light audible click will be heard when the linkage is released.
  4. Move the steering column fully forward and to the highest position.
  5. Remove the bolt that attaches the LH 1st row outboard side shield to the seat assembly.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  6. Release the clips (x7) that attach the LH 1st row outboard side shield to the seat assembly, disconnect the electrical connector, and then lift the side shield over the pretensioner to remove it from the vehicle.

Install

  1. Position the LH 1st row outboard side shield to the seat assembly, connect the electrical connector, and then secure the clips (x7) that attach the side shield to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace any missing or damaged clips.
    Informational PurposesAn informational icon, calling your attention
    Note
    Guide the pretensioner through the opening.
  2. Install the bolt that attaches the LH 1st row outboard side shield to the seat assembly.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Move the steering column back to the original position.
  4. Install the front seat belt linkage to the pretensioner:
    1. Make sure the lock screw is in the horizontal position. If the lock screw is not in the horizontal position, follow the release instructions to unlock it.
    2. Verify there are no twists in the seat belt from the upper B-pillar trim to the pretensioner.
    3. Install the linkage onto the pretensioner cable.
      Informational PurposesAn informational icon, calling your attention
      Note
      An audible click will be heard.
      Informational PurposesAn informational icon, calling your attention
      Note
      The lock screw will rotate back to the locked position.
    4. Perform a firm pull test on the seat belt with at least 15 pounds of force.
  5. Restore the LH front seat back to its original position.
  6. Raise the LH front window and close the LH front door.