02/08/2024 09:52:49

Dash Panel - Instrument Panel Lower Assembly (Remove and Install)

Correction code 1405027081 FRT 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-04-11: Added a note to avoid damaging the blue tape that protects harness from glove box mechanism.
  • 2024-03-07: Revised quantity of x4 screws, T20 securing the RH lower IP to the vehicle.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the front doors and lower the front windows.
  2. Remove the LH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  3. Remove the LH lower A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Lower Trim - LH (Remove and Install).
  4. Remove the footwell cover. See Dash Support Frame - Footwell Cover (Remove and Install).
  5. Repeat steps 2 and 3 for the RH side of the vehicle.
  6. Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  7. Disconnect MV power. See Disconnect MV Power.
  8. Remove the mid instrument panel assembly. See Dash Panel - IP Mid Panel Assembly (Remove and Install).
  9. Remove the screws (x4) that attach the lower instrument panel to the vehicle.
    2 Nm (1.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  10. Remove and discard the bolts (x4) that attach the lower instrument panel to the vehicle.
    7 Nm (5.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  11. Release the panel clips (x15) and push clip that attach the lower instrument panel to the vehicle, and then release the panel from the IP.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Avoid tearing the blue tape that holds the harness slack at the RH side of the lower IP panel. The tape must be in place to protect the harness from contact with the glove box mechanism.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not release the panel too far from the IP as there are connectors (x4) still connected.
  12. Disconnect the electrical connectors (x4), and then remove the lower instrument panel from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the connector locks before disconnecting the connectors.

Install

  1. Position the lower instrument panel into the vehicle, and then connect the electrical connectors (x4) and engage the connector locks.
  2. Secure the panel clips (x15) and push clip that attach the lower instrument panel to the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Avoid tearing the blue tape that holds the harness slack at the RH side of the lower IP panel. The tape must be in place to protect the harness from contact with the glove box mechanism. Replace the blue tape if damaged.
  3. Install the screws (x4) that attach the lower instrument panel to the vehicle.
    2 Nm (1.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  4. Install new bolts (x4) that attach the lower instrument panel to the vehicle.
    7 Nm (5.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Install the mid instrument panel assembly. See Dash Panel - IP Mid Panel Assembly (Remove and Install).
  6. Reconnect MV power. See Disconnect MV Power.
  7. Install the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  8. Install the RH lower A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Lower Trim - LH (Remove and Install).
  9. Install the RH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  10. Install the footwell cover. See Dash Support Frame - Footwell Cover (Remove and Install).
  11. Repeat steps 8 and 9 for the LH side of the vehicle.
  12. Raise the front windows and close the front doors.