2026-03-03

Bracket Upper - Bed - LH (Long Range) (Remove and Install)

Correction code 12150300101 12150300102 1.26 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.
  • 2026-02-26: Released new procedure.
  1. Open tailgate
    Informational PurposesAn informational icon, calling your attention
    Note
    Press button to release, Use manual release as necessary
  2. Remove fastener covers from bed floor assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    14x covers
  3. Remove bed floor assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Lift front edge with trim tool then remove panel, Recommend assistance
  4. Remove LH sail applique
    Informational PurposesAn informational icon, calling your attention
    Note
    15x clips, 1x connector, 1x harness clip, Lift rear edge first to remove connector and harness clip
  5. Remove LH upper bed side wall assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    13x clips, Start from rear, Pull from the bottom downwards
  6. Remove LH bed closeout panel
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 1x tab, Release LH tailgate cable by disengaging lock spring from bolt and sliding cable eyelet off to allow removal of bed closeout panel from vehicle
  7. Remove LH lower bed side wall
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers
  8. Remove RH sail applique
    Informational PurposesAn informational icon, calling your attention
    Note
    15x clips
  9. Remove RH upper bed side wall assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    13x clips, Start from rear, Pull from the bottom downwards
  10. Remove RH bed closeout panel
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 1x tab, Release RH tailgate cable by disengaging lock spring from bolt and sliding cable eyelet off in order to remove bed closeout panel from vehicle
  11. Remove RH bed side wall
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers
  12. Remove false wall
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 15mm, 45 Nm. Recommended to use assistance
  13. Remove LH upper bed bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 13mm, 30Nm
  14. Install LH upper bed bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 13mm, 30Nm
  15. Install false wall
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 15mm, 45 Nm. Recommended to use assistance
  16. Install RH bed side wall
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers
  17. Install RH bed closeout panel
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 1x tab, Release RH tailgate cable to install bed closeout panel from vehicle
  18. Install RH upper bed side wall assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    13x clips, Replace any missing or damaged clips
  19. Install RH sail applique
    Informational PurposesAn informational icon, calling your attention
    Note
    13x clips, Replace any damaged clips
  20. Install LH lower bed side wall
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers
  21. Install LH bed closeout panel
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 1x tab, Secure LH tailgate cable once closeout installed
  22. Install LH upper bed side wall assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    13x clips, Replace any missing or damaged clips, Lift tonneau seal as required
  23. Install LH sail applique
    Informational PurposesAn informational icon, calling your attention
    Note
    15x clips, 1x connector, 1x harness clip, Replace any broken clips
  24. Install bed floor assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Recommend assistance
  25. Install fastener covers onto bed floor assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    14x covers
  26. Close tailgate