2026-06-12

Seat Assembly - 2nd Row (Remove and Replace)

Correction code 13050401201 13050401202 FRT 1.74 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and its associated FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.
Warning
Cybertruck electronics are powered by a 48V "mid voltage" or "MV" architecture that is designed to improve efficiency. Servicing MV components requires extra knowledge and care in order to avoid personal and/or vehicular harm. Read and understand MV precautions in Electrical Precautions and make sure any required MV-related training courses have been completed, as applicable.
  • 2026-06-12: Released new procedure.

Remove

  1. Open all four doors
  2. Lower all four windows
  3. Manually latch all doors to prevent lockout
    Note
    Engage latch with screwdriver
  4. Enter Service Mode. See Service Mode.
  5. Raise and move LH front seat forward
  6. Move RH front seat forward
  7. Disconnect MV power. See Mid-Voltage Power (Disconnect and Connect) (Modify).
  8. Close LH and RH visors and retract LH and RH windshield shade assemblies
  9. Remove the LH and RH 2nd row seatback shoulder covers. See Shoulder Cover - LH - 2nd Row Seat (Remove and Install).
  10. Remove the rear vehicle controller. See Body Controller - Rear (Remove and Install).
  11. Release all connections from charge port ecu
    Note
    3x connectors
  12. Remove charge port ECU
    Note
    1x bolts, 10 mm, 5 Nm, 2x tabs
  13. Release 2nd row center retractor from 2nd LH row buckle
    Note
    Push red release mechanism to release retractor
  14. Remove bolts securing 2nd row seat back onto the back wall
    Note
    4x bolts, 10mm, 9 Nm, 2x bolts, 10mm, 7 Nm
  15. Remove bolts securing lower 2nd row full seat assembly onto the back wall
    Note
    8x bolts, 15mm, 50 Nm
  16. Remove bolts securing LH and center/RH 2nd row buckle onto 2nd row seat assembly
    Note
    2x bolts, 15mm, 40 Nm
  17. Remove bolts securing 2nd row seat assembly onto vehicle structural frame
    Note
    4x bolts, 15mm, 50 Nm
  18. Remove LH 2nd row shoulder cover
    Note
    7x clips, 1x datum
  19. Release RH 2nd row shoulder cover
    Note
    7x clips, 1x datum
  20. Release 2nd row center seat belt from 2nd row seat assembly
    Note
    1x button
  21. Remove 2nd row seat assembly
    Note
    Recommend assistance

Install

  1. Install 2nd row seat assembly
    Note
    Assistance recommended for safe installation onto frame
  2. Install 2nd row center seat belt onto 2nd row seat assembly
    Note
    1x button
  3. Install RH 2nd row shoulder cover
    Note
    7x clips, 1x datum
  4. Install LH 2nd row shoulder cover
    Note
    7x clips, 1x datum
  5. Install bolts securing 2nd row seat assembly onto vehicle structural frame
    Note
    4x bolts, 15mm, 50 Nm
  6. Install the rear vehicle controller. See Body Controller - Rear (Remove and Install).
  7. Install bolts securing LH and center/RH 2nd row buckle onto 2nd row seat assembly
    Note
    2x bolts, 15mm, 40 Nm
  8. Install bolts securing lower 2nd row full seat assembly onto the back wall
    Note
    8x bolts, 15mm, 50 Nm
  9. Install bolts securing 2nd row seat back assembly onto the back wall
    Note
    4x bolts, 10mm, 9 Nm, 2x bolts, 10mm, 7 Nm
  10. Secure 2nd row center retractor onto 2nd LH row buckle
    Note
    Push red release mechanism to release retractor
  11. Install charge port ECU
    Note
    1x bolt, 10 mm, 5 Nm, 2x tabs, Align charge port ecu into cavity for installation
  12. Secure all connections to charge port ecu connectors
    Note
    3x connectors
  13. Reinstall all components that were removed for access. See Shoulder Cover - LH - 2nd Row Seat (Remove and Install).
  14. Connect mid-voltage power. See Mid-Voltage Power (Disconnect and Connect) (Modify).
  15. Move RH front seat to original position
  16. Lower and move LH front seat to original position
  17. Exit Service Mode. See Service Mode.
  18. Raise all four windows.
  19. Close all four doors.