23/07/2024 17:25:53

Bed Side Wall - Bed Side Wall - LH (Remove and Install)

Correction code 1215016021 1215016022 1215016031 1215016032 FRT 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Remove the bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
  2. Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  3. Disconnect MV power. See Disconnect MV Power.
  4. Remove the LH and RH bed cargo tub struts. See Tonneau - Bed Cargo Tub Strut (Remove and Install).
  5. Remove the bed cargo tub lid. See Bed Cargo Tub - Bed Cargo Tub Lid (Remove and Replace).
  6. Starting from the rear, release the clips (x8) that attach the LH upper bed side wall assembly to the vehicle, and then remove the side wall from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift the tonneau seal as needed.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull from the bottom downwards.
  7. Remove LH lower bed side wall
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 15mm, 46 Nm, 2x bolts, T45, 36 Nm, 4x bolts, 10mm, 11 Nm, 2x nuts, 10mm, 7 Nm, 4x clips, 1x fastener cover, 1x connector, Release locking tabs, Disconnect bed outlet connectors from bed side wall and ground strap, 1x bolt, 10mm, 10 Nm, 2x connectors, Release locking tabs, Slide lock to release, Recommend assistance

Install

  1. Install LH lower bed side wall
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 15mm, 46 Nm, 2x bolts, T45, 36 Nm, 4x bolts, 10mm, 11 Nm, 2x nuts, 10mm, 7 Nm, 4x clips, 1x fastener cover, 1x connector, Secure locking tabs, Connect bed outlet connectors onto bed side wall and ground strap, 1x bolt, 10mm, 10 Nm, 2x connectors, Secure locking tabs, Slide lock to secure, Recommend assistance
  2. Position the LH upper bed side wall assembly to the vehicle, and then secure the clips (x8) that attach the side wall to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift the tonneau seal as needed.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace any missing or damaged clips.
  3. Install the bed cargo tub lid. See Bed Cargo Tub - Bed Cargo Tub Lid (Remove and Replace).
  4. Install the LH and RH bed cargo tub struts. See Tonneau - Bed Cargo Tub Strut (Remove and Install).
  5. Install the bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
  6. Reconnect MV power. See Disconnect MV Power.
  7. Install the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  8. Close the tonneau cover.