Floor Y Duct - 2nd Row (Remove and Install)
Correction code
1810084121
1810084122
FRT
0.72
NOTE: Unless
otherwise explicitly stated in the procedure, the above correction code and
FRT reflect all of the work required to perform this procedure, including
the linked procedures. Do
not stack correction codes unless explicitly told to do so.
NOTE: See Flat Rate Times to learn more about FRTs and how they are
created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com.
NOTE: See Personal Protection to make
sure wearing proper PPE when performing the below procedure. See Ergonomic Precautions for safe and healthy
working practices.
Remove
- Remove the LH front seat carpet. See Carpet Assembly - Driver (Remove and Install).
- Remove the center floor upper bracket. See Bracket - Upper - Center Floor (Remove and Install).
-
Release the clips (x4) that attach the
center lower support bracket to the vehicle, and then remove the support bracket from
the vehicle.
- Remove the 2nd row duct on rails. See Duct On Rails - 2nd Row (Remove and Install).
-
Release the clip that attaches the 2nd
row floor Y-duct to the vehicle, release the Y-duct from the passenger side duct, and
then maneuver the Y-duct out of the vehicle.
Install
-
Position the 2nd row floor Y-duct into
the vehicle, secure the Y-duct into the passenger side duct, and then install the clip
that attaches the Y-duct to the vehicle.
-
Install the 2nd row dual duct on rails
into the vehicle.
NoteManeuver as needed through foam insert.
-
Install the center lower support bracket into the vehicle, and then secure the clips
(x4) that attach the support bracket to the vehicle.
-
Position the center floor upper
bracket into the vehicle, and then install the edge clips (x2), retaining clips (x2),
and push clips (x2) that attach the bracket to the vehicle.
- Install the center floor trim. See Trim - Center Floor - Lower (Remove and Install).
-
Unfold the RH front cabin carpet into
position.
- Install the RH center floor rail. See Rail - Center Floor - LH (Remove and Install).
- Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Install).
- Install the RH mid A-pillar trim. See Trim - A-Pillar - Mid - LH (Remove and Install).
-
Install the RH front door seal.
-
Install driver carpet assembly.
NoteThe plastic portions at the rear of the carpet need to clear risers.
-
Maneuver the LH seat riser crossmember
into position, and then install the bolt that attaches the crossmember to the outboard
riser.35 Nm (25.8 lbs-ft)TIpUse of the following tool(s) is recommended:
- 13 mm socket
-
Install the bolts (x2) that attach the
crossmember to the inboard riser.9 Nm (6.6 lbs-ft)TIpUse of the following tool(s) is recommended:
- 10 mm socket
-
Unfold the LH front cabin carpet into
position.
- Install the accelerator pedal. See Accelerator Pedal (Remove and Install).
- Install the accelerator pedal side trim. See Side Trim - Pedal (Remove and Install).
- Install the LH center floor rail. See Rail - Center Floor - LH (Remove and Install).
- Install the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Install).
- Install the LH mid A-pillar trim. See Trim - A-Pillar - Mid - LH (Remove and Install).
-
Install the LH side lower A-pillar
primary seal.
- Install the footwell cover. See Cover - Footwell (Remove and Install).
- Restore the RH front seat back to its original position.
- Raise the RH front window and close the RH front door.
- Restore the LH front seat back to its original position.
- Raise the LH front window and close the LH front door.