11/12/2024 11:41:15

Door Glass - Moving Glass - Rear LH (Remove and Install)

Correction code 1020030021 1020030022 1020030031 1020030032 FRT 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-12-11: Added new caution about Pre-Installation Glass Inspection service requirements.
  • 2024-05-13: Added step and warning to support glass while removing regulator fasteners.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
New glass components (windshield, roof, door, and fixed glass) must be inspected before installation to meet Tesla’s internal standards of quality. Perform the inspection described in Pre-Installation Glass Inspection before beginning this procedure.

Remove

  1. Open the LH rear door and lower the LH rear window.
  2. Remove the LH rear door beltline assembly. See Rear Door Trim Pad - Beltline Assembly - LH (Remove and Install).
  3. Remove the LH rear door inner waist belt seal. See Front and Rear Door Seals - Inner Waist Belt Seal, Rear Door, LH (Remove and Install).
  4. Remove the LH rear door trim. See Rear Door Trim Pad - Door Trim Rear - LH (Remove and Install).
  5. Remove the LH rear door grommets (x4).
  6. Connect an external window switch.
  7. Raise the LH rear window.
  8. With the help of an assistant, hold the door glass in position before continuing to the next step.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The clamps do not hold the entire regulator base. Failure to support the glass while removing the fasteners in the next step may result in the glass slipping off the regulator.
  9. With the assistant supporting the glass, remove the bolts (x2) that attach the LH rear door glass to the vehicle, and then remove the glass from the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Make sure to support the glass while removing the fasteners. The clamps do not hold the entire base of the regulator.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket

Install

  1. Position the LH rear door glass into the vehicle, and then install and hand tighten the bolts (x2) that attach the glass to the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be careful of the glass slipping off the mount.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  2. Pull the emergency cable to manually unlatch the LH rear door.
  3. Close the LH rear door.
  4. Check and adjust gap and flushness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Connect an external window switch to help with adjustment.
  5. Open the LH rear door.
  6. Torque the fasteners for window regulator, and then install the grommets (x2).
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  7. Disconnect the external window switch.
  8. Install the LH rear door inner waist belt seal. See Front and Rear Door Seals - Inner Waist Belt Seal, Rear Door, LH (Remove and Install).
  9. Install the LH rear door trim. See Rear Door Trim Pad - Door Trim Rear - LH (Remove and Install).