Tie Rod - Outer - LH - Front Steering Gear (Long Range) (Remove and Install)
Correction code
NEW
NOTE: Unless
otherwise explicitly stated in the procedure, the above correction code and
FRT reflect all of the work required to perform this procedure, including
the linked procedures. Do
not stack correction codes unless explicitly told to do so.
NOTE: See Flat Rate Times to learn more about FRTs and how they are
created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com.
NOTE: See Personal Protection to make
sure wearing proper PPE when performing the below procedure.
- 2025-06-21: Released new procedure.
-
Raise and support vehicle
NoteSet air suspension to "Jack Mode"
-
Open LH front door
NotePush LH B-pillar door trigger to release
- Lower LH front window
-
Remove LH front wheel cap
Note1x cap, 8x clips, Use both hands to firmly pull wheel cap to release clips, Cap may remove with or without mounting ring attached
-
Loosen LH front wheel nuts
Note6x nuts, 21mm, 205 Nm
-
Raise vehicle fully
NoteSet to a comfortable working height, Lower to locks, Ensure locks engage on both sides to prevent tilting
-
Remove rear skid plate
Note6x clips, 3x bolts, 15mm, 42 Nm, 5x bolts, 13mm, 28 Nm, 2x bolts, 10mm, 6 Nm
-
Lower vehicle partially and set lift onto locks
NoteRaise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height
-
Remove LH front wheel
Note6x nuts, 21mm, 205 Nm
-
Loosen LH outer tie rod end jam nut
Note1x nut, 24mm, 90 Nm
-
Remove nut securing LH tie rod end to knuckle
Note1x nut, 21mm, 170 Nm
- Remove LH tie rod end from knuckle
-
Remove LH outer tie rod end from front steering rack assembly
NoteCount how many turns it takes to fully remove and write this down you will need it when installing the tie rod end again
-
Install LH outer tie rod end onto front steering rack assembly
NoteTurn the outer tie rod end exactly the amount of rotations it took to remove it, This ensures the alignment is as close as possible to where it was originally
- Position LH tie rod end onto knuckle
-
Install nut securing LH tie rod end to knuckle
Note1x nut, 21mm, 170 Nm
-
Secure tie rod end jam nut
Note1x nut, 24mm, 90 Nm
-
Install LH front wheel
Note6x nuts, 21mm, 205 Nm
-
Raise vehicle fully
NoteSet to a comfortable working height, Lower to locks, Ensure locks engage on both sides to prevent tilting
-
Install rear skid plate
Note6x clips, 3x bolts, 15mm, 42 Nm, 5x bolts, 13mm, 28 Nm, 2x bolts, 10mm, 6 Nm, Apply Loctite 222 to mid aero shield bolts and install fasteners
-
Lower vehicle until tires are touching the ground
NoteRaise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
-
Torque LH front wheel nuts
Note6x nuts, 21mm, 205 Nm, Use star pattern
-
Install LH front wheel cap
Note1x cap, 8x clips, Partially secure wheel cap to wheel, While partially installed wheel cover can be rotated to align with tire design, When aligned press inward from center of cap then secure all clips to mounting ring
-
Remove vehicle from lift
NoteLower rack arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"
- Raise LH front window
- Close LH front door
-
Perform test drive
NotePerform a validation test drive after repairDrive a minimum speed of 25mph, Drive in a straight line and check for excessive pull, Verify the steering wheel is centered when vehicle is driving straight, Determine whether an alignment is recommendedAdd correction code 00040100 as needed