Rear Stabilizer Bar and Links - Rear Stabar Assembly (Remove and Install)
Correction code 3103098031 FRT 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.
Remove
- Open the LH front door and lower the LH front window.
- Put the vehicle in Service Mode. See Service Mode.
- Open the powered frunk.
- Disconnect MV power. See Disconnect MV Power.
- Remove the LH and RH rear wheel caps. See Wheel Cover - Front - LH (Remove and Install).
-
Loosen the LH and RH wheel lug nuts
(x6 each wheel)..Tip: Use of the following tool(s) is recommended:
- 21 mm deep socket
- Raise and support the vehicle on a 2 post lift. See Raise Vehicle - 2 Post Lift.
- Remove the LH rear aft fender flare. See Front and Rear Garnish - Rear Fender Flare Aft - LH (Remove and Install).
- Remove the LH rear aft fender flare carrier. See Front and Rear Garnish - Carrier - Rear Fender Flare Aft - LH (Remove and Install).
- Remove the RH rear fender flare. See Front and Rear Garnish - Rear Fender Flare - RH (Remove and Install).
- Remove the RH rear aft fender flare carrier. See Front and Rear Garnish - Carrier - Rear Fender Flare Aft - RH (Remove and Install).
- Remove the rear fascia. See Rear Bumper Fascia - Rear Fascia (Remove and Install).
- Remove the LH and RH rear wheels. See Wheel Assembly (Remove and Install).
- Remove the LH and RH rear stabar links. See Rear Stabilizer Bar and Links - Rear Stabar Link - LH (Remove and Install).
-
Release the clip and remove the bolts
(x4) that attach the rear stabar assembly to the vehicle.Tip: Use of the following tool(s) is recommended:
- 15 mm socket
NoteManeuver the stabar outwards between the fascia braces.
Install
-
Install the bolts (x4) and fasten the
clip that attach the rear stabar assembly to the body.Tip: Use of the following tool(s) is recommended:
- 15 mm socket
NoteManeuver the stabar inwards between the fascia braces. - Install the LH and RH rear stabar links. See Rear Stabilizer Bar and Links - Rear Stabar Link - LH (Remove and Install).
- Install the LH and RH rear wheels. See Wheel Assembly (Remove and Install).
- Install the rear fascia. See Rear Bumper Fascia - Rear Fascia (Remove and Install).
- Install the LH rear aft fender flare carrier. See Front and Rear Garnish - Carrier - Rear Fender Flare Aft - LH (Remove and Install).
- Install the LH rear aft fender flare. See Front and Rear Garnish - Rear Fender Flare Aft - LH (Remove and Install).
- Install the RH rear aft fender flare carrier. See Front and Rear Garnish - Carrier - Rear Fender Flare Aft - RH (Remove and Install).
- Install the RH rear fender flare. See Front and Rear Garnish - Rear Fender Flare - RH (Remove and Install).
- Install the LH and RH rear wheel caps. See Wheel Cover - Front - LH (Remove and Install).
- Reconnect MV power. See Disconnect MV Power.
- Close the Powergate.
- Remove the vehicle from the lift. See Raise Vehicle - 2 Post Lift.
- Exit Service Mode. See Service Mode.
- Raise the LH front window and close the LH front door.