23/07/2024 17:30:37

Front Suspension Arms - Front Upper Arm Assembly - LH (Remove and Install)

Correction code 3101065011 3101065012 3101065021 3101065022 FRT 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Table 1. Torque Specifications: Front Suspension
Description Torque Value Recommended Tools Reuse/Replace Notes
Nut that attaches the LH front upper control arm to the LH front knuckle
80 Nm (59.0 lbs-ft)
  • 18 mm socket
 Reuse
Nuts (x4) that attach the LH front upper control arm to the vehicle
50 Nm (36.9 lbs-ft)
  • 15 mm socket
 Replace
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Raise and support the vehicle. See Raise Vehicle - 2 Post Lift.
  3. Remove the LH front wheel. See Wheel Assembly (Remove and Install).
  4. Remove the LH front wheel liner. See Wheel Arch Liners - Front Wheel Liner - LH (Remove and Replace).
  5. Position and raise pole jack onto the LH front lower control arm.
  6. Disconnect the LH front air suspension height sensor connector.
  7. Remove and discard the nut that attaches the LH front upper control arm to the knuckle.
    80 Nm (59.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use a step ladder as needed.
    Tip: Use of the following tool(s) is recommended:
    • 18 mm socket
  8. Remove the LH front air suspension height sensor assembly. See Height Controller and Sensors - Front Air Suspension Height Sensor Assembly - LH (Remove and Install).
  9. Remove and discard the nuts (x4) that attach the LH front upper control arm assembly to the vehicle, and then remove the control arm from the vehicle.
    50 Nm (36.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket

Install

  1. Position the LH front upper control arm assembly into the vehicle, and then install new nuts (x3) that attach the control arm to the vehicle.
    50 Nm (36.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
  2. Position the LH front air suspension height sensor into the vehicle, and then install the sensor linkage onto the ball stud on the upper control arm assembly.
  3. Position the LH front air suspension height sensor to the body, and then install a new nut that attaches the sensor to the upper control arm mount.
    50 Nm (36.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
  4. Install a new nut that attaches the LH front upper control arm to the knuckle.
    80 Nm (59.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use a step ladder as needed.
    Tip: Use of the following tool(s) is recommended:
    • 18 mm socket
  5. Connect the LH front air suspension height sensor connector.
  6. Lower and remove pole jack from the LH front lower control arm.
  7. Install the LH front wheel liner. See Wheel Arch Liners - Front Wheel Liner - LH (Remove and Replace).
  8. Install the LH front wheel. See Wheel Assembly (Remove and Install).
  9. Remove the vehicle from the lift. See Raise Vehicle - 2 Post Lift.
  10. Raise the LH front window and close the LH front door.