23/07/2024 17:24:00

Air Suspension Compressor and Reservoir - Air Compressor Exhaust Assembly (Remove and Install)

Correction code 3110008031 3110008032 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Place the vehicle into Service Mode. See Service Mode.
  3. Open the tonneau cover.
  4. Open the tailgate.
  5. Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  6. Disconnect MV power. See Disconnect MV Power.
  7. Remove the bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
  8. Release the clips (x4) that attach the air compressor harness to the vehicle, and then disconnect the harness electrical connectors (x3).
  9. Remove the nuts (x3) that attach the air suspension compressor carrier bracket to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  10. Remove the bolts (x4) that attach the air suspension compressor bracket to the air compressor.
    5.5 Nm (4.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 socket
  11. Move the air suspension bracket aside to access the air line inlet fitting.
  12. Remove the air compressor exhaust assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull back the collar of the fitting, and then pull the exhaust outward to release it.

Install

  1. Install the air compressor exhaust assembly into the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push the exhaust inward firmly to secure it.
    Informational PurposesAn informational icon, calling your attention
    Note
    Perform a push-pull-push test to ensure the hose is fully engaged.
  2. Reposition the air suspension bracket.
  3. Install the bolts (x4) that attach the air suspension compressor bracket to the air compressor.
    5.5 Nm (4.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 socket
  4. Install the nuts (x3) that attach the air suspension compressor carrier bracket to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  5. Connect the air compressor harness electrical connectors (x3), and then secure the clips (x4) that attach the air compressor harness to the vehicle.
  6. Install the bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
  7. Reconnect MV power. See Disconnect MV Power.
  8. Install the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  9. Close the tonneau cover.
  10. Close the tailgate.
  11. Exit Service Mode. See Service Mode.
  12. Raise the LH front window and close the LH front door.