11/09/2024 10:27:20

Bed and Backbone Harnesses - Bed Left (Remove and Install)

Correction code 1710013011 1710013012 FRT 2.58 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-09-11: Added note and link for testing and servicing Super Connectors.
  • 2024-05-29: Updated locking cover torque value from 4 Nm to 6 Nm.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Cybertruck electronics are powered by a 48V "mid voltage" or "MV" architecture that is designed to improve efficiency. Servicing MV components requires extra knowledge and care in order to avoid personal and/or vehicular harm. Read and understand MV precautions in Electrical Precautions and make sure any required MV-related training courses have been completed, as applicable.
Informational PurposesAn informational icon, calling your attention
Note
For best practices associated with testing and servicing Super Connectors on a Cybertruck Vehicle Controller, refer to video Super Controller Testing.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open all the doors and lower all the windows.
  2. Use a pocket screwdriver to manually latch all the doors to prevent lockout.
  3. Place the vehicle into Service Mode. See Service Mode.
  4. Open the tonneau cover.
  5. Open the tailgate.
  6. Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  7. Disconnect MV power. See Disconnect MV Power.
  8. Remove the frunk assembly. See Frunk Assembly (Remove and Install).
  9. Remove the LH underhood apron. See Underhood Trim - Side Apron Assembly - LH (Remove and Install).
  10. Remove the LH outer cantrail. See Closure Panels - Assembly - Cantrail - Left (Remove and Install).
  11. Remove the LH sail baffle applique. See Exterior Trim Fittings - Sail Baffle Applique - LH (Remove and Install).
  12. Remove the LH sail baffle closeout. See Exterior Trim Fittings - Sail Baffle Closeout - LH (Remove and Install).
  13. Remove the LH rear fore fender flare. See Front and Rear Garnish - Rear Fender Flare Fore - LH (Remove and Install).
  14. Remove the LH rear fore fender flare carrier. See Front and Rear Garnish - Carrier - Rear Fender Flare Fore - LH (Remove and Install)
  15. Remove the LH rear aft fender flare. See Front and Rear Garnish - Rear Fender Flare Aft - LH (Remove and Install).
  16. Remove the LH rear aft fender flare. See Front and Rear Garnish - Carrier - Rear Fender Flare Aft - LH (Remove and Install).
  17. Remove the chargeport door. See Charge Port - Charge Port Door (Remove and Install).
  18. Remove the bolts (x2) that attach the charge port assembly onto the body.
    6 Nm (4.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm 12-point deep socket
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only hand tools. Risk of galling if power tools are used on stainless bolts.
  19. Remove the bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
  20. Remove the LH sail applique. See Truck Bed Exterior Trim - Sail Applique Assembly - LH (Remove and Replace).
  21. Remove the LH tonneau water management seal. See Tailgate Seals - Tonneau Water Management Seal, LH, Center (Remove and Install).
  22. Remove the LH rear lamp closeout applique. See Truck Bed Exterior Trim - Rear Lamp Closeout Applique - LH (Remove and Install).
  23. Remove the LH upper bed side wall. See Truck Bed Exterior Trim - Upper Bed Side Wall Assembly - LH (Remove and Install).
  24. Remove the LH rear bed closeout. See Truck Bed - Rear Bed Closeout - LH (Remove and Install).
  25. Remove the LH lower bed side wall. See Bed Side Wall - Bed Side Wall - LH (Remove and Install).
  26. With an assistant holding the LH outer bed side, remove the fasteners (x14) that attach the outer bed side to the vehicle, and then remove the panel from the vehicle and place it on a padded surface.
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • Torx T25 socket
  27. Remove the rear fascia assembly. See Rear Bumper Fascia - Rear Fascia (Remove and Install).
  28. Remove the front header trim. See Headliner Trim - Front Header Trim (Remove and Install).
  29. Remove the LH mid A-pillar trim. See A-B-C Positivet Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  30. Remove the LH upper A-pillar trim. See A-B-C Positivet Interior Trim - A-Pillar Upper Trim - LH (Remove and Install).
  31. Remove the rear header trim. See Headliner Trim - Rear Header Trim (Remove and Install).
  32. Remove the LH cantrail trim. See Headliner Trim - Cantrail Trim - LH (Remove and Install).
  33. Release the clips (x7) and datum that attach the LH 2nd row shoulder cover to the body, and then remove the cover from the vehicle.
  34. Remove the LH 2nd row seat back outboard bolster. See 2nd Row Seat Assemblies - 2R Seat Side Bolster LH (Remove and Install).
  35. Remove the LH 2nd row seat back inboard bolster. See 2nd Row Seat Assemblies - 2R Seat Back Inboard Bolster LH (Remove and Install).
  36. Remove the LH lower C-pillar trim. See A-B-C Positivet Interior Trim - C-Pillar Lower Trim - LH (Remove and Install).
  37. Remove the LH upper C-pillar trim. See A-B-C Positivet Interior Trim - C-Pillar Upper Trim - LH (Remove and Install).
  38. Remove the charge port ECU. See Charge Port - Assembly Charge Port Controller ECU Gen 4 (Remove and Replace).
  39. Remove the LH 2nd row seat back assembly. See 2nd Row Seat Assemblies - 2nd Row Seat Back Assembly - LH (Remove and Install).
  40. Slowly loosen the bolt that secures the locking cover to the rear controller, making sure that the cover separates from the controller squarely, and does not bind.
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not remove locking cover. Loosen until the bolt spins freely.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the bolt and locking cover are fully released before attempting to release the connectors.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the cover binds, tighten the bolt until the locking cover is square again, then loosen the bolt while holding the cover square to the controller.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use a power tool to loosen the bolt.
    Figure 1. Rear MV controller shown; other MV controllers similar
  41. Disconnect the LH bed harness electrical connector from the rear MV controller.
    Informational PurposesAn informational icon, calling your attention
    Note
    The connector has two tabs, one on the top right side and one on the left lower side of the connector head. Both tabs must be pressed inwards for the connector head to clear the locking cover and release successfully.
    Tip: Use a pocket screwdriver to press one of the connector tabs while pressing the other tab by hand.
  42. Disconnect the electrical connectors (x4) and release the clips (x5) at the lower interior section of the LH bed harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the connector locks before disconnect the electrical connectors.
  43. Disconnect the electrical connector and release the clips (x5) at the upper interior section of the LH bed harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the connector lock before disconnecting the electrical connector.
  44. Release the tabs (x6) that attaches the grommet to the body, and then pull the harness outwards to remove it.
  45. Disconnect the electrical connectors (x6) and release the harness clips (x18) at the forward section of the LH bed harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the connector locks before disconnecting the electrical connectors.
  46. Remove the bolt that attaches the LH bed harness at the rear upper section.
    7 Nm (5.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  47. Disconnect the electrical connectors (x2) and release the clips (x9) at the rear upper section of the LH bed harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the connectors lock before disconnecting the electrical connectors.
  48. Disconnect the electrical connectors (x4) and release the harness clips (x7) at the rear lower section of the LH bed harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the connector locks before disconnecting the connectors.
  49. Remove the LH bed harness from the vehicle.

Install

  1. Position the LH bed harness into the vehicle.
  2. Connect the electrical connectors (x4) and install the harness clips (x7) at the rear lower section of the LH bed harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Connecting the electrical connectors, and then engage the connector locks.
  3. Connect the electrical connectors (x2) and install the clips (x9) at the rear upper section of the LH bed harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Connecting the electrical connectors, and then engage the connector locks.
  4. Install the bolt that attaches the LH bed harness at the rear upper section.
    7 Nm (5.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Connect the electrical connectors (x6) and install the harness clips (x18) at the forward section of the LH bed harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Connecting the electrical connectors, and then engage the connector lock.
  6. Position the grommet to the body, and then pull the harness inwards to install it.
  7. Connect the electrical connector and secure the clips (x5) at the upper interior section of the LH bed harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Connect the electrical connectors, and then engage the connector locks.
  8. Connect the electrical connectors (x4) and secure the clips (x5) at the lower interior section of the LH bed harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Connect the electrical connectors, and then engage the connector locks.
  9. Connect the LH bed harness at to the rear MV controller.
  10. Slowly tighten the bolt that secures the locking cover to the rear controller, making sure that the cover is square to the controller, and does not bind.
    6 Nm (4.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
    Informational PurposesAn informational icon, calling your attention
    Note
    If the cover binds, loosen the bolt until the locking cover is square again, then tighten the bolt while holding the cover square to the controller.
    Tip: While tightening the bolt, press the connector into the controller to keep it square.
    Figure 2. Rear MV controller shown; other MV controllers similar
  11. Install the LH 2nd row seat back assembly. See 2nd Row Seat Assemblies - 2nd Row Seat Back Assembly - LH (Remove and Install).
  12. Install the charge port ECU. See Charge Port - Assembly Charge Port Controller ECU Gen 4 (Remove and Replace).
  13. Install the LH upper C-pillar trim. See A-B-C Positivet Interior Trim - C-Pillar Upper Trim - LH (Remove and Install).
  14. Install the LH lower C-pillar trim. See A-B-C Positivet Interior Trim - C-Pillar Lower Trim - LH (Remove and Install).
  15. Install the LH 2nd row seat back inboard bolster. See 2nd Row Seat Assemblies - 2R Seat Back Inboard Bolster LH (Remove and Install).
  16. Install the LH 2nd row seat back outboard bolster. See 2nd Row Seat Assemblies - 2R Seat Side Bolster LH (Remove and Install).
  17. Position the LH 2nd row shoulder cover into the vehicle, and then fasten the clips (x7) and datum that attach the cover to the vehicle.
  18. Install the LH cantrail trim. See Headliner Trim - Cantrail Trim - LH (Remove and Install).
  19. Install the rear header trim. See Headliner Trim - Rear Header Trim (Remove and Install).
  20. Install the LH upper A-pillar trim. See A-B-C Positivet Interior Trim - A-Pillar Upper Trim - LH (Remove and Install).
  21. Install the LH mid A-pillar trim. See A-B-C Positivet Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  22. Install the front header trim. See Headliner Trim - Front Header Trim (Remove and Install).
  23. Install the rear fascia assembly. See Rear Bumper Fascia - Rear Fascia (Remove and Install).
  24. Install the RH rear aft fender flare carrier. See Front and Rear Garnish - Carrier - Rear Fender Flare Aft - RH (Remove and Install).
  25. Install the RH rear fender flare. See Front and Rear Garnish - Rear Fender Flare - RH (Remove and Install).
  26. With an assistant, position the LH outer bed side onto the vehicle, and then install and hand tighten the fasteners (x14) that attach the outer bed side to the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • Torx T25 socket
  27. With an assistant, adjust the LH outer bed side to within gap and flushness specification, and then torque the fasteners (x14) that attach the outer bed side to the vehicle.
    28 Nm (20.6 lbs-ft)
    8 Nm (5.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The torque values are as follows:
    • 13 mm bolts (x13) - 28 Nm
    • T25 screw - 8 Nm
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • Torx T25 socket
  28. Install the LH lower bed side wall. See Bed Side Wall - Bed Side Wall - LH (Remove and Install).
  29. Install the LH rear bed closeout. See Truck Bed - Rear Bed Closeout - LH (Remove and Install).
  30. Install the LH upper bed side wall. See Truck Bed Exterior Trim - Upper Bed Side Wall Assembly - LH (Remove and Install).
  31. Install the LH rear lamp closeout applique. See Truck Bed Exterior Trim - Rear Lamp Closeout Applique - LH (Remove and Install).
  32. Install the LH tonneau water management seal. See Tailgate Seals - Tonneau Water Management Seal, LH, Center (Remove and Install).
  33. Install the LH sail applique. See Truck Bed Exterior Trim - Sail Applique Assembly - LH (Remove and Replace).
  34. Install the bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
  35. Install the bolts (x2) that attach the charge port assembly onto the body.
    6 Nm (4.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm 12-point deep socket
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only hand tools. Risk of galling if power tools are used on stainless bolts.
  36. Install the chargeport door. See Charge Port - Charge Port Door (Remove and Install).
  37. Install the LH rear aft fender flare carrier. See Front and Rear Garnish - Carrier - Rear Fender Flare Aft - LH (Remove and Install).
  38. Install the LH rear aft fender flare. See Front and Rear Garnish - Rear Fender Flare Aft - LH (Remove and Install).
  39. Install the LH rear fore fender flare carrier. See Front and Rear Garnish - Carrier - Rear Fender Flare Fore - LH (Remove and Install)
  40. Install the LH rear fore fender flare. See Front and Rear Garnish - Rear Fender Flare Fore - LH (Remove and Install).
  41. Install the LH sail baffle closeout. See Exterior Trim Fittings - Sail Baffle Closeout - LH (Remove and Install).
  42. Install the LH sail baffle applique. See Exterior Trim Fittings - Sail Baffle Applique - LH (Remove and Install).
  43. Install the LH outer cantrail. See Closure Panels - Assembly - Cantrail - Left (Remove and Install).
  44. Install the LH underhood apron. See Underhood Trim - Side Apron Assembly - LH (Remove and Install).
  45. Reconnect MV power. See Disconnect MV Power.
  46. Install the frunk assembly. See Frunk Assembly (Remove and Install).
  47. Install the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  48. Exit Service Mode. See Service Mode.
  49. Raise all the windows and close all the doors.
  50. Close the tonneau cover.
  51. Close the tailgate.