23/07/2024 17:28:42

Front and Rear Door Glass Regulator - Window Regulator - Rear LH (Remove and Install)

Correction code 1150040031 FRT 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Put the vehicle in Service Mode. See Service Mode.
  3. Open the LH rear door and lower the LH rear window.
  4. Remove the LH rear door beltline assembly. See Rear Door Trim Pad - Beltline Assembly - LH (Remove and Install).
  5. Remove the LH rear door inner waist belt seal. See Front and Rear Door Seals - Inner Waist Belt Seal, Rear Door, LH (Remove and Install).
  6. Use a pocket screwdriver to manually latch the LH front door.
  7. Raise the LH rear window.
  8. Remove the LH rear door trim. See Rear Door Trim Pad - Door Trim Rear - LH (Remove and Install).
  9. Remove the LH rear moving glass. See Door Glass - Moving Glass - Rear LH (Remove and Install).
  10. Disconnect MV power. See Disconnect MV Power.
  11. Release the locking tabs and disconnect the LH rear door harness connectors (x4), and then release the clips (x5) that attach the harness to the LH rear door closeout panel.
  12. Remove the bolts (x13) and release the datums (x2) that attach the LH rear door closeout panel to the door assembly, and then remove the closeout panel from the door assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Gently pry the panel to release the datums (x2).
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the bottom portion of the panel away from the door assembly, and then lower the assembly to allow clearance for the regulator rails.
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
    • 10 mm socket
  13. Remove the bolts (x4) and release the datums (x4) that attach the LH rear window regulator to the closeout panel.
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket

Install

  1. Position the LH rear window regulator to the closeout panel, and then install the bolts (x4) and secure the datums (x4) that attach window regulator to the closeout panel.
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
  2. Position the LH rear door closeout panel to the door assembly, and then install the bolts (x13) and datums (x2) that attach the closeout panel to the door assembly.
    4 Nm (2.9 lbs-ft)
    12 Nm (8.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Torque the 8mm bolts (x11) to 4 Nm, and the 10 mm bolts (x2) to 12 Nm.
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
    • 10 mm socket
  3. Connect the LH rear door harness connectors (x4) and secure the connector locks, and then install the clips (x5) that attach the harness to the LH rear door closeout panel.
  4. Install the LH rear moving glass. See Door Glass - Moving Glass - Rear LH (Remove and Install).
  5. Install the LH rear door inner waist belt seal. See Front and Rear Door Seals - Inner Waist Belt Seal, Rear Door, LH (Remove and Install).
  6. Install the LH rear door trim. See Rear Door Trim Pad - Door Trim Rear - LH (Remove and Install).
  7. Install the LH rear door beltline assembly. See Rear Door Trim Pad - Beltline Assembly - LH (Remove and Install).
  8. Raise the LH rear window and close the LH rear door.
  9. Raise the LH front window and close the LH front door.