2024-07-23

Demist Duct - Driver (Remove and Install)

Correction code 1405077081 1405077082 FRT 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the front doors and lower the front windows.
  2. Remove the LH mid A-pillar trim. See Trim - A-Pillar - Mid - LH (Remove and Install).
  3. Remove the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Install)
  4. Remove the footwell cover. See Cover - Footwell (Remove and Install).
  5. Repeat steps 2and 3 for the RH side of the vehicle.
  6. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Install).
  7. Disconnect MV power. See Disconnect MV Power (Modify).
  8. Remove the mid instrument panel assembly. See Mid Panel Assembly - Instrument Panel (Remove and Install).
  9. Remove the lower instrument panel assembly. See Lower Assembly - Instrument Panel (Remove and Install).
  10. Remove the glovebox assembly. See Glovebox Assembly (Remove and Install).
  11. Remove the RH air wave duct. See Passenger Ducting and Vents - Panel Duct, RH (Remove and Install).
  12. Remove the front passenger airbag. See Front Air Bags - MX - Passenger Airbag, NAR (Remove and Install).
  13. Remove the instrument panel top pad assembly. See Top Pad Assembly - Instrument Panel (Remove and Install)
  14. Remove the instrument panel aerobracket assembly. See Aerobracket Assembly - Instrument Panel (Remove and Install).
  15. Disconnect the driver side IP airwave module electrical connectors (x2).
  16. Disconnect the IP aerobracket assembly light strip electrical connectors (x2).
  17. Disconnect the passenger side IP airwave module electrical connectors (x2).
  18. Remove the push clip and release the clip that attach the driver demist duct assembly to the vehicle, and then remove the duct from the vehicle.

Install

  1. Position the driver demist duct assembly into the vehicle, and then secure the clip and install the push clip.
  2. Remove the instrument panel aerobracket assembly. See Aerobracket Assembly - Instrument Panel (Remove and Install).
  3. Install the instrument panel top pad assembly. See Top Pad Assembly - Instrument Panel (Remove and Install)
  4. Install the front passenger airbag. See Front Air Bags - MX - Passenger Airbag, NAR (Remove and Install).
  5. Install the RH air wave duct. See Passenger Ducting and Vents - Panel Duct, RH (Remove and Install).
  6. Install the glovebox assembly. See Glovebox Assembly (Remove and Install).
  7. Install the lower instrument panel assembly. See Lower Assembly - Instrument Panel (Remove and Install).
  8. Install the mid instrument panel assembly. See Mid Panel Assembly - Instrument Panel (Remove and Install).
  9. Reconnect MV power. See Disconnect MV Power (Modify).
  10. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Install).
  11. Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Install)
  12. Install the RH mid A-pillar trim. See Trim - A-Pillar - Mid - LH (Remove and Install).
  13. Install the footwell cover. See Cover - Footwell (Remove and Install).
  14. Repeat steps 11 and 12 for the LH side of the vehicle.
  15. Close the front doors and lower the front windows.