2026-08-09

Rear Fascia (Remove and Install)

Correction code 1001089051 FRT 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and its associated FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Put the vehicle in Service Mode. See Service Mode.
  3. Disconnect MV power. See Mid-Voltage Power (Disconnect and Connect) (Modify).
  4. Remove the LH rear aft fender flare. See Fender Flare - Aft - Rear - LH (Remove and Install).
  5. Remove the clips (x5) that attach the LH rear wheel liner to the rear fascia and diffuser.
  6. Remove the LH rear aft fender flare carrier. See Carrier - Fender Flare - Aft - Rear - LH (Remove and Install).
  7. Remove the rear license plate.
  8. Remove the bolts (x2) that attach the rear center fascia to the body.
    6 Nm (4.4 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  9. Remove the RH rear fender flare. See Fender Flare - Rear - RH (Remove and Install).
  10. Remove the RH rear aft fender flare carrier. See Carrier - Fender Flare - Aft - Rear - RH (Remove and Install).
  11. Remove the clips (x5) that attach the RH rear wheel liner to the rear fascia and diffuser.
  12. Remove the bolts (x9) that attach the rear diffuser to the body.
    6 Nm (4.4 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  13. Release the locking tab, and then disconnect the rear fascia harness electrical connector.
    Note
    The harness is located behind the rear of the LH wheel liner.
  14. With assistance, release the tabs (x16) that attach the rear fascia to the body, and then remove the fascia from the vehicle.
    Note
    Release the RH and LH sides of rear fascia from the body.
    Note
    Place the fascia onto protected surface.
    Figure 1. LH shown; RH similar
    Figure 2. LH shown; RH similar

Install

  1. With assistance, position the rear fascia to the vehicle, and then secure the clips (x16) that attach the fascia to the vehicle.
    Note
    Sides must be spread apart to clear the bumper structure.
    Figure 3. LH shown; RH similar
  2. Install the bolts (x2) that attach the rear center fascia to the body.
    6 Nm (4.4 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Install the rear license plate.
  4. Install the bolts (x9) that attach the rear diffuser to the body.
    6 Nm (4.4 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Connect the rear fascia harness electrical connector, and then secure the connector lock.
  6. Fasten the clips (x5) that attach the LH rear wheel liner to rear fascia and diffuser.
  7. Install the LH rear aft fender flare carrier. See Carrier - Fender Flare - Aft - Rear - LH (Remove and Install).
  8. Install the LH rear aft fender flare. See Fender Flare - Aft - Rear - LH (Remove and Install).
  9. Fasten the clips (x5) that attach the RH rear wheel liner to the rear fascia and diffuser.
  10. Install the RH rear aft fender flare carrier. See Carrier - Fender Flare - Aft - Rear - RH (Remove and Install).
  11. Install the RH rear fender flare. See Fender Flare - Rear - RH (Remove and Install).
  12. Reconnect MV power. See Mid-Voltage Power (Disconnect and Connect) (Modify).
  13. Exit Service Mode. See Service Mode.
  14. Raise the LH front window and close the LH front door.