23/07/2024 17:23:37
2nd Row Seat Covers and Pads - 2nd Row Seat Backrest Substrate LH (Remove and Install)
Correction code 1308005101 1308005102 FRT 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Remove
- Open the LH doors and lower the LH windows.
- Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
- Disconnect MV power. See Disconnect MV Power.
- Remove the LH 2nd row side bolster. See 2nd Row Seat Assemblies - 2R Seat Side Bolster LH (Remove and Install).
- Remove the LH 2nd row seat back inboard bolster. See 2nd Row Seat Assemblies - 2R Seat Back Inboard Bolster LH (Remove and Install).
-
Disconnect the charge port ECU
electrical connectors (x3).
-
Remove the bolt and release the tabs
(x2) that attach the charge port ECU to the vehicle, and then remove the ECU from the
vehicle.Tip: Use of the following tool(s) is recommended:
- 8 mm socket
-
Remove the bolts (x4) that attach the
LH 2nd row seat back assembly to the vehicle.Tip: Use of the following tool(s) is recommended:
- 10 mm socket
-
Release the clips (x4) that attach the
LH 2nd row substrate to the seat back frame, and then release the substrate from the
frame.
-
Release the connector lock, and then
disconnect the LH 2nd row side substrate assembly electrical connector.
-
Remove the LH 2nd row substrate
assembly from the vehicle.
-
Release the securing tabs (x13) and
side rails (x2) that attach the LH 2nd row substrate trim and foam assembly to the
substrate, and then remove the trim and foam from the assembly.
Install
-
Position the LH 2nd row substrate trim assembly to the substrate, and secure the
securing tabs (x13) and side rails (x2) that attach the trim and foam to the
assembly.
-
Position the LH 2nd row substrate
assembly into the vehicle, and then connect the electrical connector and engage the
connector lock.
-
Secure the clips (x4) that attach the LH 2nd row substrate to the seat back
frame.
-
Install the bolts (x4) that attach the LH 2nd row seat back assembly to the
vehicle.Tip: Use of the following tool(s) is recommended:
- 10 mm socket
-
Position the charge port ECU into the vehicle, and then install the bolt and secure
the tabs (x2) that attach the ECU to the vehicle.NoteAlign the charge port ECU into cavity.Tip: Use of the following tool(s) is recommended:
- 8 mm socket
-
Connect the charge port ECU electrical connectors (x3).
- Install the LH 2nd row seat back inboard bolster. See 2nd Row Seat Assemblies - 2R Seat Back Inboard Bolster LH (Remove and Install).
- Install the LH 2nd row side bolster. See 2nd Row Seat Assemblies - 2R Seat Side Bolster LH (Remove and Install).
- Reconnect MV power. See Disconnect MV Power.
- Install the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
- Close the LH doors and raise the LH windows.