23/07/2024 17:33:55

Front Seat Covers and Pads - 1R Front Seat Back Foam RH With Ventilation (Remove and Install)

Correction code 1307060101 1307060102 FRT 0.84 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Remove the LH 1st row seat assembly. See Front Seat Assemblies - 1st Row Seat Assembly - LH Drive - LH - Black (Remove and Install).
  2. Remove the LH 1st row seat outboard side shield. See Front Seat Covers and Pads - 1R LH Outboard Cybershield Fab (Remove and Install).
  3. Release the clips (x2) that attach the leading edge of the 1st row LH outboard side shield carrier to the seat assembly, slide the carrier away from the seat assembly to release the tabs (x2), and then remove the carrier from the seat assembly.
  4. Remove the LH 1st row seat inboard cover. See Front Seat Covers and Pads - 1R LH Inboard Cybershield Paint (Remove and Install).
  5. Remove the LH 1st row seat seatbelt buckle. See 1st Row Seat Belts - ZF First Row Buckle - Sumitomo (Remove and Install).
  6. Release clip that attaches the leading edge of the 1st row LH inboard side shield carrier to the seat assembly, slide the carrier away from the seat frame to release the rear clip, and then remove the carrier from the seat assembly.
  7. With assistance, place the seat on a protected surface with the underside of the seat accessible.
  8. Release the seat back elastic straps (x2) from the seat frame.
  9. Release the soft trim retainers (x2) from the seat frame.
  10. Release the soft trim retainer from the inboard and outboard sides of the seat frame.
    Figure 1. Inboard side
    Figure 2. Outboard side
  11. Release the soft trim retainer from the front end of the seat frame.
  12. Position the seat upright.
  13. Remove the seat cushion assembly from the seat frame.
  14. Release the strap on the underside of the seat cushion assembly.
  15. Feed the seat cushion harness through the seat cushion trim opening.
  16. Release the Velcro strips that attach the seat cushion trim to the seat cushion, and then release the trim to expose the hog rings (x3).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be careful to avoid tearing the Velcro from the foam.
  17. Remove and discard the hog rings (x3) that attach the seat cushion trim to the seat cushion assembly, and then remove the trim from the assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Cut the hog rings, and then remove any debris.

Install

  1. Position the seat cushion trim to the seat cushion assembly, and then install new hog rings (x3) that attach the trim to the assembly.
    Tip: Use of the following tool(s) is recommended:
    • Hog Ring Pliers (1501599-00-A)
  2. Secure the Velcro that attach the seat cushion trim to the seat cushion.
  3. Feed the seat cushion harness through the seat cushion trim opening.
  4. Pull the cushion around the foam and smooth out the material, and then secure the strap on the underside of the seat cushion assembly.
  5. Install the seat cushion assembly onto the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Feed the trim between the seat back trim and seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Maneuver the seat assembly as needed for access.
  6. Install the soft trim retainer on the inboard and outboard sides of the seat frame.
    Figure 3. Inboard side
    Figure 4. Outboard side
  7. Install the soft trim retainer on the front end of the seat frame.
  8. Rotate the seat assembly onto the seat back.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Protect the seat from damage.
  9. Install the soft trim retainers (x2) onto the seat frame.
  10. Install the seat back elastic straps (x2) onto the seat frame.
  11. Position the leading edge of the 1st row LH inboard side shield carrier to the seat assembly, and then slide the carrier onto the seat frame to secure the clips (x2) and tabs (x2).
  12. Install the LH 1st row seat inboard cover. See Front Seat Covers and Pads - 1R LH Inboard Cybershield Paint (Remove and Install).
  13. Install the LH 1st row seat seatbelt buckle. See 1st Row Seat Belts - ZF First Row Buckle - Sumitomo (Remove and Install).
  14. Slide the 1st row LH outboard side shield carrier onto the seat assembly to align the clips (x2) and tabs (x2), and then engage the fasteners that attach the carrier to the seat assembly.
  15. Install the LH 1st row seat outboard side shield. See Front Seat Covers and Pads - 1R LH Outboard Cybershield Fab (Remove and Install).
  16. Install the LH 1st row seat assembly. See Front Seat Assemblies - 1st Row Seat Assembly - LH Drive - LH - Black (Remove and Install).