23/07/2024 17:24:55

Air Suspension Compressor and Reservoir - Air Reservoir (Remove and Install)

Correction code 3110008041 3110008042 FRT 0.71 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning

This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

Raise and support the vehicle on a 2 post lift. See Raise Vehicle - 2 Post Lift.
Open the LH front door and lower the LH front window.
Deflate the air suspension system. See Air Suspension - Pressurize / Depressurize - Full System.
Open the tonneau cover.
Open the tailgate.
Remove the bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
Remove the bolt that attaches the pressurized pack valve block to the air suspension reservoir.
5 Nm (3.7 lbs-ft)
Tip: Use of the following tool(s) is recommended:
- 10 mm socket
Note
x1 electrical connector

Note
x1 clip, x1 cable tie

Note
Release the lock before connector disengagement.

Note
Cut the cable tie at the reservoir/ancillary air line bundle.

Note
Release the electrical harness clip at the bracket.
Release the air suspension valve block.

Note
x3 rubber grommets

Note
Rotate clockwise until the top 2 rubber feet have released from the bracket. Pull upwards at a 45 degree angle to release the bottom rubber foot from the bracket.

Note
Leave all air lines and connections secured, and then set the assembly aside.
Disconnect the air lines (x4) from the air suspension reservoir.
3 Nm (2.2 lbs-ft)
Tip: Use of the following tool(s) is recommended:
- 10 mm 12 point combination wrench
- 14 mm 12 point combination wrench
Note
torque: 7 Nm (14 mm); 5 Nm (10 mm)

Note
x4 VOSS fittings

Note
Discard the air line fittings after removal.
Remove the nuts (x2) that attach the air suspension reservoir to the body, and then remove the reservoir from the vehicle.
33 Nm (24.3 lbs-ft)
Tip: Use of the following tool(s) is recommended:
- 13 mm 12-point socket
Note
x2 fir tree clips

Install

Install the nuts (x2) that attach the air suspension reservoir to the body.
33 Nm (24.3 lbs-ft)
Tip: Use of the following tool(s) is recommended:
- 13 mm 12-point socket
Note
x2 fir tree clips
Install the air lines (x4) onto the air suspension reservoir.
Tip: Use of the following tool(s) is recommended:
- 10 mm deep socket
- 14 mm deep socket
Note
torque: 7 Nm (14 mm); 5 Nm (10 mm)

Note
x4 VOSS fittings

Note
Install new VOSS fittings.

Note
Remove the plastic caps from the VOSS fittings. Press the air lines into the fitting until the mark aligns with the top of the fitting. Verify the line is properly secured by performing a push-pull test.
Secure the air suspension valve block.

Note
x3 rubber grommets

Note
Rotate counterclockwise until the top 2 rubber feet are secured onto the bracket. Push downwards at a 45 degree angle to secure the bottom rubber foot into the bracket. Position the air lines and connections into place for installation.
Install the bolt that attaches the pressurized pack valve block to the air suspension reservoir.
5 Nm (3.7 lbs-ft)
Tip: Use of the following tool(s) is recommended:
- 10 mm socket
Note
x1 electrical connector

Note
x1 clip, x1 cable tie

Note
Secure the air suspension reservoir and ancillary air lines at the white marked sections.
Install the bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
Close the tonneau cover.
Close the tailgate.
Refill the air suspension system reservoir. See Air Suspension - Pressurize / Depressurize - Full System.
Raise the LH front window and close the LH front door.