15/01/2025 15:18:08

2nd Row Seat Covers and Pads - 2nd Row Seat Buckle Closeout Split - LH (Remove and Replace)

Correction code NA NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning

This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Open LH rear door

Note
Push LH C-pillar door trigger to release
Lower LH rear window
Partially release LH rear primary door seal
Remove LH lower C-pillar trim

Note
3x clips, 7x tabs, 4x datums, Starting at door sill pull upward then forward to release, Leave trim attached to seat belt
Remove 2nd row seatback LH outboard bolster

Note
2x tabs, 1x datum, 3x clips, Release tab near the bottom of LH outboard bolster, Partially release LH 2nd row shoulder cover and remove bolster from vehicle
Fold up 2nd row 60 seat

Note
Pull tether to release then lift up until locked in place
Open RH rear door

Note
Push RH C-pillar door trigger to release
Lower RH rear window
Fold up 2nd row 40 seat

Note
Pull tether to release then lift up until locked in place
Partially release RH lower C-pillar trim

Note
1x clip, 1x datum
Remove rear wall lower trim

Note
2x push clips, 4x clips, Remove outermost push clips, then pull straight forward to release inner clips
Fold down 2nd row 40 seat

Note
Pull tether to release then pivot down until locked in place
Disconnect LH 2nd row cushion assembly connectors

Note
3x connectors, 5x clips
Remove LH 2nd row seat cushion outboard cover

Note
1x clip, Pull outward from lower forward section to release
Release LH 2nd row cushion from underbelly

Note
Pull plastic retainers outward to release from underbelly
Remove LH 2nd row seat underbelly

Note
8x clips, Pull outwards from bottom to release
Remove LH 2nd row cushion assembly

Note
6x clips, Lift upwards off seat frame
Remove LH 2nd row seat buckle split closeout assembly

Note
2x clips, 1x datum
Install LH 2nd row seat buckle split closeout assembly

Note
2x clips, 1x datum
Install LH 2nd row cushion assembly

Note
6x clips, Lower onto seat frame
Install LH 2nd row seat underbelly

Note
8x clips, Push inwards to engage clips
Secure LH 2nd row cushion to underbelly

Note
Secure plastic retainers in channel
Install LH 2nd row seat cushion outboard cover

Note
1x clip, Pull outward from lower forward section to release
Fold up 2nd row 40 seat

Note
Pull tether to release then lift up until locked in place
Connect LH 2nd row cushion assembly connectors

Note
3x connectors, 5x clips
Install rear wall lower trim

Note
2x push clips, 4x clips
Fold down 2nd row 40 seat

Note
Pull tether to release then pivot down until locked in place
Fold down 2nd row 60 seat

Note
Pull tether to release then pivot down until locked in place
Install LH lower C-pillar tr

Note
3x clips, 7x tabs, 4x datums
Secure LH rear primary door seal
Install 2nd row seatback LH outboard bolster

Note
2x tabs, 1x datum, 3x clips, Position LH outboard bolster into place, Ensure all clips and tabs are fully engaged, Replace any missing or damaged clips, Secure LH 2nd row shoulder cover, Perform push-pull-push test
Raise LH rear window
Close LH rear door
Install RH lower C-pillar trim

Note
1x clip, 1x datum
Raise RH rear window
Close RH rear door

Cybertruck Service Manual

2nd Row Seat Covers and Pads - 2nd Row Seat Buckle Closeout Split - LH (Remove and Replace)

Figure 1

Figure 2

Figure 3