2026-04-02

Center Console Assembly (Remove and Replace)

Correction code 1519023132 FRT 0.71 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2026-04-02: Updated steps to latest time study. Added steps for software reinstall.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.

Remove

  1. Open all the doors and lower all the windows.
  2. Move the front seats fully forward.
  3. Release the clips (10x) and tabs (x3) that attach the center console back panel to the center console, disconnect the electrical connectors (x3), and then remove the panel from the center console assembly.
  4. Remove the bolts (x2) that attach the rear of the center console to the riser.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Remove the LH and RH center floor rails. See Rail - Center Floor - LH (Remove and Install).
  6. Remove the center console front panel. See Panel - Front - Center Console (Remove and Install).
  7. Remove the bolts (x4) that attach the front of the center console to the riser.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  8. Disconnect the center console harness electrical connectors (x2).
    Informational PurposesAn informational icon, calling your attention
    Note
    Connector count may vary depending on vehicle build.
  9. Lift the center console upwards to release it from the riser, and then remove the center console from the vehicle.

Install

  1. Position the center console into the vehicle, and then lower the center console onto the riser.
  2. Connect the center console harness electrical connectors (x2).
    Informational PurposesAn informational icon, calling your attention
    Note
    Connector count may vary depending on vehicle build.
  3. Install the bolts (x4) that attach the front of the center console to the riser.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  4. Install the center console front panel. See Panel - Front - Center Console (Remove and Install).
  5. Install the LH and RH center floor rails. See Rail - Center Floor - LH (Remove and Install).
  6. Move the front seats forward.
  7. Install the bolts (x2) that attach the rear of the center console to the riser.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  8. Position the center console rear panel to the center console assembly, connect the electrical connectors (x3), and secure the clips (x10) and tabs (x3) that attach the panel to the center console.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace any missing or damaged clips.
  9. Place the vehicle into Service Mode. See Service Mode.
  10. On the vehicle touchscreen, navigate to Service Mode > Software Reinstall, and then tap Reinstall to reinstall the vehicle software.
    Informational PurposesAn informational icon, calling your attention
    Note
    Reinstall will begin immediately. Once the software redeploy is complete, verify release notes are present via UI.
  11. Exit Service Mode. See Service Mode.
  12. Restore the LH and RH front seats back to their original position.
  13. Raise all the windows and close all the doors.