2026-05-11

HV Harness - AC Compressor (Standard) (Remove and Install)

Correction code NEW NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Warning

This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.

Warning

Cybertruck electronics are powered by a 48V "mid voltage" or "MV" architecture that is designed to improve efficiency. Servicing MV components requires extra knowledge and care in order to avoid personal and/or vehicular harm. Read and understand MV precautions in Electrical Precautions and make sure any required MV-related training courses have been completed, as applicable.

2026-05-08: Released new procedure.

Remove the tonneau slats. See Slat System - Tonneau (Remove and Install).
Partially release aft section of LH front fender flare cover

Note
11x clips, 3x datum, 1x connector total, Release as needed for clearance, Full removal not required
Remove LH front rocker fastener from step reinforcement

Note
1x bolt, 10mm, 4 Nm
Remove clip securing LH front wheel liner to rocker cover

Note
1x clip
Partially release fore section of LH rear fender flare cover

Note
13x clips, 3x datums total, Release as needed for clearance, Full removal not required
Remove LH rear rocker fastener from step reinforcement

Note
1x bolt, 10mm, 4 Nm
Remove clip securing LH rocker cover to rear wheel liner

Note
1x clip
Remove rocker cover fasteners from LH side ski

Note
6x bolts, 10mm, 10 Nm
Release LH rocker cover from rocker carrier

Note
11x clips, 1x datum, Remove any clips that remained on carrier
Remove front LH rocker step reinforcement

Note
3x bolts, 10mm, 15 Nm, 2x datums
Remove rear LH rocker step reinforcement

Note
3x bolts, 10mm, 15 Nm
Partially release LH rear primary door seal
Remove LH mid A-pillar trim

Note
1x clip, 3x tabs, Release tabs then slightly bend live hinge and release clip
Remove LH lower A-pillar trim

Note
7x clips, 3x datums, 2x tabs, Release sill plate, Pull rearward then upward
Remove footwell cover

Note
3x clips, 3x magnets, 1x bolt, 10mm, 3 Nm, Bolt is captive to tether
Remove LH front floor mat
Remove LH center floor rail

Note
4x clips, 3x datums, Pull upwards to release
Remove accelerator pedal side trim

Note
3x clips, Lift from forward edge then slide over accelerator pedal
Remove accelerator pedal

Note
2x nuts, 13mm, 10 Nm, 1x connector, Release locking tab
Remove LH carpet support foam

Note
Lift up from rear edge
Fold back LH front cabin carpet
Remove LH front interior HV Battery mounting bolts

Note
3x bolts, 24mm, 160 Nm
Temporarily install accelerator pedal

Note
2x nuts, 13mm, 10 Nm, 1x connector, Secure nuts hand tight to allow vehicle to be driven onto lift
Remove LH lower B-pillar trim

Note
2x push clips, 11x clips, 4x datums, 4x seal retainers, 2x hooks, Release bottom rear section first
Partially release aft section of front RH fender flare cover

Note
11x clips, 3x datum, 1x connector total, Release as needed for clearance, Full removal not required
Remove RH front rocker fastener from step reinforcement

Note
1x bolt, 10mm, 4 Nm
Remove clip securing RH rocker cover to front wheel liner

Note
1x clip
Partially release fore section of rear RH fender flare cover

Note
13x clips, 3x datums total, Release as needed for clearance, Full removal not required
Remove RH rear rocker fastener from step reinforcement

Note
1x bolt, 10mm, 4 Nm
Remove clip securing RH rocker cover to rear wheel liner

Note
1x clip
Remove rocker cover fasteners from RH side ski

Note
6x bolts, 10mm, 10 Nm
Release RH rocker cover from rocker carrier

Note
11x clips, 1x datum, Remove any clips that remained on carrier
Remove front RH rocker step reinforcement

Note
3x bolts, 10mm, 15 Nm, 2x datums
Remove rear RH rocker step reinforcement

Note
3x bolts, 10mm, 15 Nm
Remove RH mid A-pillar trim

Note
1x clip, 3x tabs, Release tabs then slightly bend live hinge and release clip
Remove RH lower A-pillar trim

Note
7x clips, 3x datums, 2x tabs, Release sill plate, Pull rearward then upward
Remove RH front floor mat
Remove RH center floor rail

Note
4x clips, 3x datums, Pull upwards to release
Remove center floor trim

Note
17x clips, Release upper section first
Fold back RH carpet

Note
8x clips, 4x datums
Remove RH carpet support foam

Note
Lift up from rear edge
Remove RH interior front HV battery mounting bolts

Note
3x bolts, 24mm, 160 Nm
Remove RH lower B-pillar trim

Note
2x push clips, 11x clips, 4x datums, 4x seal retainers, Release bottom rear section first
Move vehicle onto lift

Note
Ensure positioning allows rear doors to open, NOTE: If burning odors, popping sounds, flames, or smoke is seen at any time, halt this process and call the fire department immediately! Begin evacuation if vehicle is in the shop.
Install Universal Lift Pad adapters

Note
4x Adapters, Remove original lift pads from lift arms then install respective adapter, Remove plugs from BIW holes, Align pins with lift point holes on body
Raise and support vehicle

Note
Set air suspension to "Jack Mode", Align lift adapter pins with lift point holes on body
Select "Coolant Fill/Drain" through Service UI

Note
Select 'Coolant System' to enter coolant circuit screen, Select 'Coolant Fill/Drain' and 'PROC_VCFRONT_X_START-THERMAL-FILL-DRAIN-COOLANT' window will appear, Select 'Run', Verify indicator displays green for Coolant readiness, Thermal Fill Drain routine has a 50 minute time limit
Open powered front trunk

Note
Via exterior switch or UI
Power off vehicle from center display

Note
Verify EPBs are engaged, Select charge port icon to ensure drive state is disengaged then power down vehicle via Controls > Safety > Power Off
Remove rear underhood apron

Note
9x clips
Remove frunk assembly

Note
6x bolts, 10mm, 12 Nm, 2x bolt caps, 2x bumpstops, 1x connector, Remove bolt covers from frunk floor, Remove washer fluid cap by gently prying upwards, Rotate bumpstops counter clockwise to release, the 25mm socket from PT Sensor kit can be used, Avoid straining emergency frunk release connector
Disconnect first responder loop and MV battery connector

Note
2x connectors, Release locking tab then disconnect FRL connector, Slide eCPA to left then lift lever to release MV battery connector, Early production trucks may have black FRL connector, Release eCPA by pushing down to unlock and slide red locking tab, Wait 2 minutes for electrical circuits to discharge before disconnecting modules
Verify operation of multimeter

Note
Set multimeter to DC voltage, Confirm multimeter is properly measuring voltage by testing MV battery, Touch lightly and do not damage terminals
Raise vehicle fully and lower lift onto locks

Note
Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
Remove aero shield fasteners

Note
17x bolts, 10mm, 6 Nm, Open bolt lids
Remove front skid plate

Note
8x nuts, 15mm, 50 Nm, 2x bolts, 11mm, 50 Nm
Remove mid-aero shield

Note
6x clips, 3x bolts, 15mm, 42 Nm, 5x bolts, 13mm, 28 Nm, 2x bolts, 10mm, 6 Nm(*15mm & 10mm bolts not shown in catalog, feedback sent)
Remove all items from pockets and ensure not wearing metal items

Note
This includes phones, badges, metal belt buckles airpods and headphones
Inspect HV insulating gloves

Note
Check gloves for damage prior to use, Refer to service document TN-15-92-003, for information on inspecting HV gloves.
Put on HV insulating gloves and leather over gloves

Note
Use HV cut resistant insulated gloves or HV insulating gloves and leather over gloves, HV Insulating gloves must be worn any time a Hioki Tester or Hi-Pot Tester is used, Refer to service document TN-15-92-003 R5 for PPE requirements depending on vehicle configuration
Verify no HV - Install amp clamp to RDU HV harness

Note
Verify meter is zeroed out before performing measurement, Measure single cable. Verify ammeter is installed in correct direction. If current > 0.5A do not proceed with disconnecting HV connector. In this case, start vehicle electrical isolation again to make sure that all was properly shut down. Escalate for assistance as requiredIf current < 0.5A, Ok to disconnect and check voltage at HV plug on the battery side.Release locking tab and rotate the release lever up to disengage the connector, Release harness clip, Do not force the release lever up, Ensure the alignment tabs on the RDU header are not damagedMake sure to wear PPE (HV gloves, safety glasses) when working on high voltage component, Measure B+ to Ground, B- to Ground, B+ to B-, If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering
Remove leather over gloves and HV insulating gloves
Lower vehicle until tires are touching the ground

Note
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
Disconnect HV harness connector from AC compressor

Note
1x locking electrical connector, Pull red locking tab away from compressor then slide black lock upwards to release
Fold up 2nd row 60 seat

Note
Pull tether to release then lift up until locked in place
Remove 2nd row floor mat
Partially release LH lower C-pillar trim

Note
1x clip, 1x datum
Release LH MV controller dry side locking cover

Note
1x bolt, 8mm, 6 Nm, Do not remove locking cover, Loosen until bolt spins freely, Double check that bolt and locking cover are fully released before attempting to release any MV connectors, Plastic Locking CoverUse hand tools on any plastic locking covers, The locking cover may release crooked causing it to get stuck, secure bolt a few turns to loosen the tension then release bolt while assisting plastic locking cover by gently prying on the side that's stuck, Metal Locking CoverYou can use power tools, Quickly disconnecting locking cover helps connectors remove symmetrically, Video uses rear controller for demonstration purposes only
Release floor harness from LH MV controller

Note
1x connector, 1x clip, Depress tabs to release connector housing from locking cover
Fold up 2nd row 40 seat

Note
Pull tether to release then lift up until locked in place
Release RH MV controller connector lower locking cover

Note
1x bolt, 8mm, 6 Nm, Do not remove locking covers, Loosen until bolts spins freely, Double check that bolts and locking covers are fully released before attempting to release any MV connectorsPlastic Locking Cover Use hand tools on any plastic locking covers, The locking covers may release crooked causing them to get stuck, secure bolts a few turns to loosen the tension then release bolts while assisting plastic locking covers by gently prying on the stuck sidesMetal Locking Cover You can use power tools, Quickly disconnecting locking covers helps connectors remove symmetrically
Release cabin floor and backbone harnesses from RH MV controller

Note
1x connector, 1x backbone cable, 2x edge clips, 3x harness clips, Pull from edges of connector housing, Do not pull backbone cable, Avoid bending cable at a tight radius
Disconnect rear display connector from car computer

Note
1x connector
Partially release RH lower C-pillar trim

Note
1x clip, 1x datum
Remove rear wall lower trim

Note
2x push clips, 4x clips, Remove outermost push clips, then pull straight forward to release inner clips
Remove RH subwoofer

Note
1x connector, 2x bolts, 13mm, 8 Nm, Slide towards center of vehicle to release outer port from body
Remove RH rear interior HV battery mounting bolts

Note
4x bolts, 13mm, 60 Nm, Bolts on both sides of stanchion, Some vehicles may have a mix of 13mm and 15mm bolts
Disconnect backbone harness from rear MV controller

Note
1x connector, 1x bolts, 8mm, 6 Nm, Do not remove locking cover, Loosen until bolt spins freely, Double check that bolt and locking cover has fully released before attempting to release any MV connectors, Depress tabs on connector housing to releasePlastic Locking CoverUse hand tools on any plastic locking covers, The locking covers may release crooked causing them to get stuck, Thread bolt a few turns to avoid damage then gently pry stuck edges of locking coverMetal Locking CoverYou can use power tools, Quickly disconnecting locking covers helps connectors release evenly
Remove LH subwoofer

Note
1x connector, 2x bolts, 13mm, 8 Nm, Slide towards RH of vehicle to release outer port from body, Release locking tab
Remove fastener covers from bed floor assembly

Note
14x covers
Remove bed floor assembly

Note
12x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Lift front edge with trim tool then remove panel, Recommend assistance
Remove fasteners securing RH tonneau NVH barrier

Note
6x bolts, T25, 5 Nm, Vehicles built before April 2024 will have 1-piece NVH cover, 5x bolts, 8mm, 5 Nm, Vehicles built after April 2024 will have updated 1-piece NVH cover, 9x bolts, 4mm Allen, 5 Nm, Vehicles built after October 2024 will have 2-piece NVH cover*part number for bolts needed
Remove RH tonneau NVH barrier

Note
Vehicles built before April 2024 will have 1-piece NVH cover, Vehicles built after April 2024 will have updated 1-piece NVH cover, Vehicles built after October 2024 will have 2-piece NVH cover, Maneuver around bed wall then remove
Remove fasteners securing LH tonneau NVH barrier

Note
5x bolts, T25, 5 Nm, Vehicles built before April 2024 will have 1-piece NVH cover, 5x bolts, 8mm, 5 Nm, Vehicles built after April 2024 will have updated 1-piece NVH cover, 9x bolts, 4mm Allen, 5 Nm, Vehicles built after October 2024 will have 2-piece NVH cover
Remove LH tonneau NVH barrier

Note
Vehicles built before April 2024 will have 1-piece NVH cover, Vehicles built after April 2024 will have updated 1-piece NVH cover, Vehicles built after October 2024 will have 2-piece NVH cover, Maneuver around bed wall then remove
Remove bolts securing HV battery to RUB

Note
4x bolts, 21mm, 119 Nm, Break free before using power tools, Tonneau slats must be closed or removed to access forward bolts, Shown without tonneau for clarity
Disconnect ancillary bay MV connector

Note
1x connector, Double locking, Release tab then pivot lever, Release second tab to disengage connector, Wait 1 second between locking tab release to discharge and prevent arcing
Remove bolt securing busbar HV connector lid

Note
1x bolt, EP10, 9 Nm
Remove bolts securing HV connector to DC FC header

Note
2x bolts, 10mm, 9 Nm
Release HV connector from DC FC header

Note
1x connector, Use inflatable airbag if needed to suspend busbar assembly above ancillary assembly
Support HV Busbar assembly

Note
1X Bungee, Suspend assembly to maintain clearance, wrap bungee around busbar assembly to achieve required cord length, Connect bungee to tie down hook on bed side
Disconnect HV ancillary harness

Note
1x connector, Release red locking tab then slide open black lever to remove
Raise vehicle fully

Note
Set to a comfortable working height, Lower to locks, Ensure locks engage on both sides to prevent tilting
Position coolant drain container underneath RH rear of HV battery
Disconnect RDU return hose from PT return hose

Note
1x spring clip, 1x clamp clip, Move wheel liner aside as needed, Plug coolant connections as needed
Disconnect RDU supply hose

Note
1x spring clip, Plug hoses
Move coolant drain container to front right of HV battery
Disconnect PT supply and return hoses

Note
2x spring clips, Plug hoses
Disconnect battery coolant supply and return hoses

Note
2x spring clips, Use caution with pick near HV harness, Plug Hoses, Position coolant drain as needed
Remove coolant drain container from underneath vehicle
Release clips securing LH pressurized pack line

Note
3x clips
Release A/C compressor HV harness from HV battery

Note
1x locking connector, 4x clips, Pull down red locking tab and disengage the release lever, Do not force the release lever up, Number of connections may vary by vehicle configuration
Disconnect RDU HV harness

Note
1x connector, Release locking tab and rotate release lever up, Do not force release lever up, Ensure alignment tabs on header are not damaged
Release FDU HV harness

Note
1x connector, 1x bolt, 10mm, 10 Nm, Move harness clear of subframe
Position battery table

Note
Ensure table is level
Remove front exterior HV Battery mounting bolts and ground strap

Note
6x bolts, 18mm, 115 Nm, 1x bolt, 10mm, 10 Nm, Ensure ground strap is clear of battery
Remove side exterior HV battery mounting bolts from LH and RH side

Note
16x bolts, 15mm, 62 Nm
Raise vehicle away from HV battery

Note
Ensure no coolant hoses, harnesses, or brake lines are caught while lifting, If lift is shorter then remove rear wheels as needed
Remove AC compressor HV harness

Note
11x clips
Install AC compressor HV harness

Note
11x clips, Ensure routing will not cause pinch or rubbing
Install HV battery alignment rods

Note
4x alignment rods, Hand tight, Install 2x larger rods onto front casting, Install 2x smaller rods onto seat stancion mounting holes on pack, New battery packs may not yet have threads in the required holes. Suggest installing bolt to create threads prior to rod installation, It is not recommended to use any holes other than instructed
Position rear carpet section for install

Note
Insert a wheel chock under carpet section to maintain 90 degree angle
Lower vehicle onto HV battery

Note
Ensure no coolant hoses, harnesses, or brake lines are caught while lowering, Recommend assistance to ensure good alignment whilst lowering
Install side exterior HV battery mounting bolts to LH and RH side

Note
16x bolts, 15mm, 60 Nm
Remove HV battery alignment rods from front casting

Note
2x alignment rods
Install front exterior HV Battery mounting bolts and ground strap

Note
6x bolts, 18mm, 115 Nm, 1x bolt, 10mm, 10 Nm
Raise vehicle away from battery table

Note
Set to a comfortable working height, Ensure lift is lowered onto a lock
Remove battery table from under vehicle
Install FDU HV harness

Note
1x connector, 1x bolt, 10mm, 10 Nm, Ensure locking tab engages
Secure A/C compressor HV harness onto battery

Note
1x locking connector, 4x clips, Engage locking tab, Do not force lever up, Number of connections may vary by vehicle configuration
Install RDU HV harness

Note
1x connector, 1x harness clip, Ensure locking tab is engaged
Install clips securing pressurized pack line

Note
3x clips
Position coolant drain container underneath RH rear of HV battery
Connect RDU return hose to PT return hose

Note
1x spring clip, Remove coolant plugs, Pull back wheel liner as required, Perform a push-pull-push test to ensure hose is engaged
Connect RDU supply hose

Note
1x spring clip, Remove coolant plugs, Perform a push-pull-push test to ensure hose is engaged
Move coolant drain container to front right of HV battery
Connect PT supply and return hoses

Note
2x spring clips, Remove plugs, Perform a push-pull-push test to ensure hose is engaged
Connect battery supply and return coolant hoses

Note
2x edge clips, 2x spring clips, Remove plugs, Secure edge clips to casting, Perform a push-pull-push test to ensure hose is engaged
Remove coolant drain container from underneath vehicle
Install Mid-aero shield

Note
6x clips, 3x bolts, 15mm, 70 Nm, 3x bolts, 13mm, 28 Nm, 2x bolts, 10mm, 6 Nm
Install front skid plate

Note
8x nuts, 15mm, 50 Nm, 2x bolts, 11mm, 50 Nm
Install front aero shield fasteners

Note
17x bolts, 10mm, 6 Nm, Apply Loctite 222 to aero shield fasteners, Close bolt lids
Lower vehicle until tires are touching the ground

Note
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
Connect HV harness connector to AC compressor

Note
1x locking electrical connector, Slide down black lock then push in red locking tab, Perform a push-pull-push test, Ensure red locking tab is fully engaged, Black tab will protrude from red locking tab when engaged correctly, Refer to images and video for clarity
Install bolts securing HV battery to RUB

Note
4x bolts, 21mm, 115 Nm, Tonneau must be closed or removed to access forward bolts, Shown without tonneau for clarity
Clean HV connector contact surface of residual Penetrox

Note
Allow 1 minute dry time after removing Penetrox, New busbar comes with Penetrox applied to HV connector
Clean busbar HV connector contact surface of residual Penetrox

Note
Allow 1 minute dry time after removing Penetrox, It is necessary to clean HV connector during re-use of busbar
Apply Penetrox onto HV connector joints

Note
Apply 2 drops of Penetrox A-13 about 5mm in diameter to either side of the hole on both leads, Spread evenly to verify the contact surface is fully covered
Install busbar onto HV header and install bolts

Note
2x bolts, 10mm, 9 Nm
Connect HV ancillary harness

Note
1x connector, Slide black lever to engage then push in red locking tab
Inspect HV insulating gloves

Note
Check gloves for damage prior to use, Refer to service document TN-15-92-003, for information on inspecting HV gloves.
Put on HV insulating gloves and leather over gloves
Perform Hioki resistance test at each HV joint from HV busbar lead to bolt head

Note
2x HV joints, When using Hioki tester, verify the meter has been properly adjusted and set prior to usageThe acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).If the resistance is greater than 0.195 mΩ (195 μΩ), stop work and escalate the Toolbox session.If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), hioki test passed, proceed to next step
Remove leather over gloves and HV insulating gloves
Install bolt securing busbar HV connector lid

Note
1x bolt, EP10, 9 Nm
Connect ancillary bay MV connector

Note
1x connector, double locking, Rotate lever into 2nd lock, Perform a pull test to ensure connector engaged correctly
Position LH tonneau NVH barrier

Note
Vehicles built before April 2024 will have 1-piece NVH cover, Vehicles built after April 2024 will have updated 1-piece NVH cover, Vehicles built after October 2024 will have 2-piece NVH cover, Maneuver around bed wall then position
Install fasteners securing LH tonneau NVH barrier

Note
5x bolts, T25, 5 Nm, Vehicles built before April 2024 will have 1-piece NVH cover, 5x bolts, 8mm, 5 Nm, Vehicles built after April 2024 will have updated 1-piece NVH cover, 9x bolts, 4mm Allen, 5 Nm, Vehicles built after October 2024 will have 2-piece NVH cover
Install bed floor assembly

Note
12x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Recommend assistance
Install fastener covers onto bed floor assembly

Note
14x covers
Inspect for any misalignment at rear ribs

Note
Ensure cable is lying flat without twist, Ensure cable is secured correctly to rib
Connect backbone harness to rear MV controller

Note
1x connector, 1x bolt, 8mm, 6 Nm, Push backbone connector housing into plastic locking cover, Ensure connector housing is secured to locking frame with a push-pull-push test, Ensure connectors are aligned before securing bracket, Secure locking cover bolt by hand initially to prevent thread stripping Plastic Locking Cover Use hand tools on any plastic locking covers, The locking cover may secure crooked causing it to get stuck, release bolt a few turns to loosen the tension then secure bolt while assist plastic locking cover by gently pushing on the side that's stuck, Push connectors too while driving the locking cover bolt to ensure correct seating Metal Locking Cover You can use power tools, Slowly drive locking cover, Ensure locking cover and bolt are seated fully
Inspect for presence of backbone harness guide at front casting

Note
Ensure backbone harness guide is installed
Connect rear display connector to car computer

Note
1x connector
Secure cabin floor and backbone harnesses onto RH MV controller

Note
1x connector, 1x backbone cable, 2x edge clips, 3x harness clips, Push from edges of connector housing, Avoid bending ribbon cable at a tight radius
Secure RH MV controller connector locking cover

Note
1x bolt, 8mm, 6 Nm, Ensure connector housing is secured to locking frame with a push-pull-push test, Ensure connectors are aligned before securing bracket, Secure locking cover bolt by hand initially to prevent thread stripping Plastic Locking Cover Use hand tools on any plastic locking covers, The locking cover may secure crooked causing it to get stuck, release bolt a few turns to loosen the tension then secure bolt while assist plastic locking cover by gently pushing on the side that's stuck, Push connectors while driving the locking cover bolt to ensure correct seating Metal Locking Cover You can use power tools, Slowly drive locking cover, Ensure locking cover and bolt
Install RH interior front HV battery mounting bolts

Note
3x bolts, 24mm, 160 Nm
Remove temporarily installed accelerator pedal

Note
2x nuts, 13mm, 10 Nm, 1x connector, Release locking tab
Secure floor harness onto LH MV controller

Note
1x connector, 1x clip, Secure in locking cover
Secure left MV controller connector locking frame

Note
1x bolt, 8mm, 4 Nm, Ensure connectors are aligned before tightening center bolt
Install LH front interior HV Battery mounting bolts

Note
3x bolts, 24mm, 160 Nm
Install LH carpet support foam

Note
Seat at rear edge
Unfold LH front cabin carpet into position
Install accelerator pedal

Note
2x nuts, 13mm, 10 Nm, 1x connector, Secure locking tab
Link to procedure: 664f759f1a55c10019c16205
Connect first responder loop and MV battery connector

Note
2x connectors, Connect FRL connector then secure locking tab, Position lever to secure MV battery connector then slide eCPA to right, Early production trucks may have black FRL connector, If power cycling vehicle then ensure at least 60 seconds has passed since powering down
Run ODIN routine
PROC_EGGRIGHT3_X_THERMAL-FILL-DRAIN-STOP
via Service Mode:
Thermal ➜ Actions ➜ Stop Thermal Fill/Drain
Thermal ➜ Coolant System ➜ Stop Coolant Fill/Drain
Thermal ➜ Refrigerant System ➜ Stop Refrigerant Fill/Drain
via Service Mode Plus:
Drive Inverter ➜ Front Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
Drive Unit ➜ Front Drive Unit Replacement ➜ Stop Coolant Fill/Drain
Drive Unit ➜ Rear Drive Unit Replacement ➜ Stop Coolant Fill/Drain
via Toolbox:(link)
Remove Universal Lift Pad adapters

Note
4x Adapters, Install original lift pads, Install plugs back into holes in BIW
Remove vehicle from lift

Note
Lower rack arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"
Select "Start Coolant Air Purge" using the UI

Note
Touch time only, wait until coolant pumps stop running (audible noise), Routine Passed will appear, but pumps will run for 10 minutes, If you start next another routine during this time it will fail, Make sure vehicle is not in "Drive", Routine is still running despite the completed message, Speeds can be monitored in garage under PT Thermal tab, Idle speed = ~1500 RPM, Test will vary speeds from 3500-6500 RPM and actuate valves between SERIES and PARALLEL, Putting vehicle into "Drive" will stop this routine, If speeds hover at 7000 RPM, this indicates the pumps are air locked, perform a vacuum fill, Continue to add coolant and purge until the coolant level reaches between the NOM and MAX Lines on the bottle
Remove battery alignment rods

Note
4x alignment rods
Install LH rear interior HV battery mounting bolts

Note
4x bolts, 13mm, 60 Nm, Bolts on both sides of stanchion, Some vehicles may have a mix of 13mm and 15mm bolts
Install LH subwoofer

Note
1x connector, 2x bolts, 13mm, 8 Nm, Slide towards LH of vehicle to secure outer port to body, Engage locking tab
Install LH lower B-pillar trim

Note
2x push clips, 11x clips, 4x datums, 4x seal retainers, 2x hooks, Secure top hooks first
Install RH rear interior HV battery mounting bolts

Note
4x bolts, 13mm, 60 Nm, Bolts on both sides of stanchion, Some vehicles may have a mix of 13mm and 15mm bolts
Install RH subwoofer

Note
1x connector, 2x bolts, 13mm, 8 Nm, Slide towards outside of vehicle to secure port
Install RH lower B-pillar trim

Note
2x push clips, 11x clips, 4x datums, 4x seal retainers
Install rear wall lower trim

Note
2x push clips, 4x clips
Secure RH lower C-pillar trim

Note
1x clip, 1x datum
Fold down 2nd row 40 seat

Note
Pull tether to release then pivot down until locked in place
Secure LH lower C-pillar trim

Note
1x clip, 1x datum
Fold down 2nd row 60 seat

Note
Pull tether to release then pivot down until locked in place
Install 2nd row floor mat
Install front RH rocker step reinforcement

Note
3x bolts, 10mm, 15 Nm, 2x datums
Install rear RH step reinforcement

Note
3x bolts, 10mm, 15 Nm
Install RH rocker cover to rocker carrier

Note
11x clips, 1x datum
Install rocker cover fasteners to RH side ski

Note
6x bolts, 10mm, 10 Nm
Install clip securing RH rocker cover to rear wheel liner

Note
1x clip
Install RH rear rocker fastener to step reinforcement

Note
1x bolt, 10mm, 4 Nm
Secure fore section of rear RH fender flare cover

Note
13x clips, 3x datums total, Ensure no clips are damaged, Replace clips as required
Install clip securing RH rocker cover to front wheel liner

Note
1x clip
Install RH front rocker fastener to step reinforcement

Note
1x bolt, 10mm, 4 Nm
Secure aft section of front RH fender flare cover

Note
11x clips, 3x datum, 1x connector total, Ensure no clips are damaged, Replace clips as required
Install RH carpet support foam

Note
Seat at rear edge
Unfold RH front cabin carpet into position
Install center floor trim

Note
17x clips, Replace any missing or damaged clips, Install lower section first
Install RH center floor rail

Note
4x clips, 3x datums
Install RH lower A-pillar trim

Note
7x clips, 3x datums, 2x tabs
Install RH mid A-pillar trim

Note
1x clip, 3x tabs, Replace any missing or damaged clips
Install RH front floor mat
Install LH front rocker step reinforcement

Note
3x bolts, 10mm, 15 Nm, 2x datums
Install rear LH step reinforcement

Note
3x bolts, 10mm, 15 Nm
Install LH rocker cover to rocker carrier

Note
11x clips, 1x datum, Replace any missing or damaged clips
Install rocker cover fasteners to LH side ski

Note
6x bolts, 10mm, 10 Nm
Install clip securing LH rear wheel liner to rocker cover

Note
1x clip
Install LH rear rocker fastener to step reinforcement

Note
1x bolt, 10mm, 4 Nm
Secure fore section of LH rear fender flare cover

Note
13x clips, 3x datums total, Replace any missing or damaged clips
Install clip securing LH front wheel liner to rocker cover

Note
1x clip
Install LH front rocker fastener to step reinforcement

Note
1x bolt, 10mm, 4 Nm
Secure aft section of LH front fender flare cover

Note
11x clips, 3x datum, 1x connector total, Replace any missing or damaged clips
Install LH center floor rail

Note
4x clips, 3x datums
Install accelerator pedal side trim

Note
3x clips, Replace any missing or damaged clips
Install footwell cover

Note
3x clips, 3x magnets, 1x bolt, 10mm, 3 Nm, Bolt is captive to tether, Replace any missing or damaged clips or magnets
Install LH Lower A-pillar trim

Note
7x clips, 3x datums, 2x tabs, Replace any missing or damaged clips
Install LH mid A-pillar trim

Note
1x clip, 3x tabs, Replace any missing or damaged clips
Install the tonneau slats. See Slat System - Tonneau (Remove and Install).

Cybertruck Service Manual

HV Harness - AC Compressor (Standard) (Remove and Install)

Figure 1

Figure 2

Figure 3