23/07/2024 17:27:39

Dash, IP and Console Harnesses - Harness - Console (Remove and Install)

Correction code 1710029041 1710029042 FRT 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Remove the center console assembly. See Center Console - Center Console Assembly (Remove and Install).
  2. Remove the center console armrest cap. See Center Console - Armrest Cap Assembly (Remove and Install).
  3. Remove the center console top decor assembly. See Center Console - Top Decor Assembly (Remove and Install).
  4. Remove the LH and RH center console external panels. See Center Console - External Panel Assembly - LH (Remove and Install).
  5. Remove the bolts (x8) that attach the airwave console cap to the center console assembly, release the mounting tabs (x7) and guiding tabs (x2), and then release the airwave console cap from the center console assembly.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  6. Disconnect the electrical connectors (x2) from the 2nd row touchscreen, disconnect the ground wire, and then release the harness fir tree clips (x2).
  7. Disconnect the 2nd row airwave module electrical connectors (x3).
  8. Release the clip that attaches the center console harness to the center bracket.
  9. Remove the bolts (x4) that attach the center console center bracket to the center console assembly, and then release the guide datums (x4) to remove the bracket from the assembly.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  10. Remove the bolts (x4) that attach the center console duct to the center console assembly, and then remove the duct from the assembly.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  11. Release the clips (x7) that attach the center console inner panel to the center console assembly, disconnect the electrical connector, and then remove the inner panel from the assembly.
  12. Disconnect the center console harness electrical connectors (x2) from the VC USB.
  13. Disconnect the center console harness electrical connector from the wireless charger.
  14. Disconnect the center console front puddle lamp.
  15. Release the clips (x5) that attach the center console harness to the center console, and then remove the harness from the assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotate the center console as needed.

Install

  1. Position the center console harness into the center console assembly, and then secure the clips (x5) that attach the harness to the assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use the outer most white clip as a starting point at the rear of the center console.
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotate the center console as needed.
  2. Connect the center console front puddle lamp.
  3. Connect the center console harness electrical connector to the wireless charger.
  4. Connect the center console harness electrical connectors (x2) to the VC USB.
  5. Position the center console inner panel to the center console assembly, connect the electrical connector, and then secure the clips (x7) that attach the inner panel to the assembly.
  6. Position the center console duct to the center console assembly, and then install the bolts (x4) that attach the duct to the assembly.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  7. Position the center console center bracket to the center console assembly, and then install the bolts (x4) that attach the bracket to the assembly.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    There will be audible click when engaging the guide datums (x4).
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  8. Secure the clip that attaches the center console harness to the center bracket.
  9. Connect the 2nd row airwave module electrical connectors (x3).
  10. Connect the electrical connectors (x2) to the 2nd row touchscreen, connect the ground wire, and then install the fir tree clips (x2).
  11. Position the airwave console cap to the center console assembly, engage the mounting tabs (x7) and guiding tabs (x2), and then install the bolts (x8) that attach the airwave console cap to the center console assembly.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  12. Install the center console armrest cap. See Center Console - Armrest Cap Assembly (Remove and Install).
  13. Install the LH and RH center console external panels. See Center Console - External Panel Assembly - LH (Remove and Install).
  14. Install the center console top decor assembly. See Center Console - Top Decor Assembly (Remove and Install).
  15. Install the center console assembly. See Center Console - Center Console Assembly (Remove and Install).