01/05/2024 15:11:22

Front Brake Rotors - Calipers and Pads - Service Front Brake Caliper Spring Kit (Remove and Install)

Correction code 3301044131 3301044132 FRT 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
  1. Open LH front door
    Informational PurposesAn informational icon, calling your attention
    Note
    Push LH B-pillar door trigger to release
  2. Lower LH front window
  3. Raise and support vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Set air suspension to "Jack Mode"
  4. Remove LH front wheel cap
    Informational PurposesAn informational icon, calling your attention
    Note
    1x cap, 8x clips, Use both hands to firmly pull wheel cap to release clips, Cap may remove with or without mounting ring attached
  5. Loosen LH front wheel nuts
    Informational PurposesAn informational icon, calling your attention
    Note
    6x nuts, 21mm, 205 Nm
  6. Raise vehicle fully
    Informational PurposesAn informational icon, calling your attention
    Note
    Set to a comfortable working height, Lower to locks, Ensure locks engage on both sides to prevent tilting
  7. Remove LH front wheel
    Informational PurposesAn informational icon, calling your attention
    Note
    6x nuts, 21mm, 205 Nm
  8. Remove brake pad anti-rattle springs from LH front brake caliper
    Informational PurposesAn informational icon, calling your attention
    Note
    2x springs, 2x tabs each
  9. Install brake pad anti-rattle springs onto LH front brake caliper
    Informational PurposesAn informational icon, calling your attention
    Note
    2x springs, 2x tabs each
  10. Install LH front wheel
    Informational PurposesAn informational icon, calling your attention
    Note
    6x nuts, 21mm, 205 Nm
  11. Lower vehicle until tires are touching the ground
    Informational PurposesAn informational icon, calling your attention
    Note
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  12. Torque LH front wheel nuts
    Informational PurposesAn informational icon, calling your attention
    Note
    6x nuts, 21mm, 205 Nm
  13. Install LH front wheel cap
    Informational PurposesAn informational icon, calling your attention
    Note
    1x cap, 8x clips, Partially secure wheel cap to wheel, While partially installed wheel cover can be rotated to align with tire design, When aligned press inward from center of cap then secure all clips to mounting ring
  14. Remove vehicle from lift
    Informational PurposesAn informational icon, calling your attention
    Note
    Lower rack arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"
  15. Raise LH front window
  16. Close LH front door
  17. Perform a road test and burnish brakes
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure proper brake pedal feel and performance Add correction code 00040100 as needed