23/07/2024 17:23:15

2nd Row Seat Assemblies - 2nd Row Seat Back Assembly - LH (Remove and Install)

Correction code 1305002101 1305002102 FRT 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Cybertruck electronics are powered by a 48V "mid voltage" or "MV" architecture that is designed to improve efficiency. Servicing MV components requires extra knowledge and care in order to avoid personal and/or vehicular harm. Read and understand MV precautions in Electrical Precautions and make sure any required MV-related training courses have been completed, as applicable.

Remove

  1. Open all the doors and lower all the windows.
  2. Use a pocket screwdriver to manually latch all the doors to prevent lockout.
  3. Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  4. Remove the front header trim. See Headliner Trim - Front Header Trim (Remove and Install).
  5. Remove the LH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  6. Remove the LH upper A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Upper Trim - LH (Remove and Install).
  7. Move the LH front seat fully forward.
  8. Place the vehicle into Service Mode. See Service Mode.
  9. Disconnect MV power. See Disconnect MV Power.
  10. Remove the rear header trim. See Headliner Trim - Rear Header Trim (Remove and Install).
  11. Partially remove the LH rear primary door seal.
  12. Remove the LH cantrail trim. See Headliner Trim - Cantrail Trim - LH (Remove and Install).
  13. Release the clips (x7) and datum that attach the LH 2nd row shoulder cover to the body, and then remove the cover from the vehicle.
  14. Remove the LH 2nd row seatback outboard bolster. See 2nd Row Seat Assemblies - 2R Seat Side Bolster LH (Remove and Install).
  15. Remove the LH 2nd row seatback inboard bolster. See 2nd Row Seat Assemblies - 2R Seat Back Inboard Bolster LH (Remove and Install).
  16. Remove the LH lower C-pillar trim. See A-B-C Post Interior Trim - C-Pillar Lower Trim - LH (Remove and Install).
    Informational PurposesAn informational icon, calling your attention
    Note
    Allow the trim to stay attached to the seat belt.
  17. Remove the LH upper C-pillar trim. See A-B-C Post Interior Trim - C-Pillar Upper Trim - LH (Remove and Install).
  18. Remove the charge port ECU. See Charge Port - Assembly Charge Port Controller ECU Gen 4 (Remove and Replace).
  19. Remove the clip that attaches the LH 2nd row seat cushion release buckle strap guide to the vehicle, and then release the guide from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Position the strap aside for access to the clip.
  20. Remove the bolts (x3) and clips (x4) that attach the LH 2nd row seat back assembly to the vehicle.
    9 Nm (6.6 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not pull the seat back assembly too far away from the vehicle as there is still an electrical connector connected.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  21. Lift the LH 2nd row seat back assembly upwards and away from frame to access the electrical connector, release the connector lock and disconnect the electrical connector, and then remove the seat back assembly from the vehicle.

Install

  1. Position the LH 2nd row seat back assembly into the vehicle, and then connect the electrical connector and engage the connector lock.
  2. Maneuver the LH 2nd row seat back assembly into position, and then install the bolts (x3) and clips (x4) that attach the assembly to the vehicle.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Maneuver the LH 2nd row seat cushion release buckle strap guide into position, and then install the clip that attaches the guide to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the strap is not twisted.
  4. Install the charge port ECU. See Charge Port - Assembly Charge Port Controller ECU Gen 4 (Remove and Replace).
  5. Install the LH upper C-pillar trim. See A-B-C Post Interior Trim - C-Pillar Upper Trim - LH (Remove and Install).
  6. Install the LH lower C-pillar trim. See A-B-C Post Interior Trim - C-Pillar Lower Trim - LH (Remove and Install).
  7. Install the LH 2nd row seatback inboard bolster. See 2nd Row Seat Assemblies - 2R Seat Back Inboard Bolster LH (Remove and Install).
  8. Install the LH 2nd row seatback outboard bolster. See 2nd Row Seat Assemblies - 2R Seat Side Bolster LH (Remove and Install).
  9. Position the LH 2nd row shoulder cover into the vehicle, and then fasten the clips (x7) and datum that attach the cover to the vehicle.
  10. Install the LH cantrail trim. See Headliner Trim - Cantrail Trim - LH (Remove and Install).
  11. Install the rear header trim. See Headliner Trim - Rear Header Trim (Remove and Install).
  12. Install the LH rear primary door seal.
  13. Reconnect MV power. See Disconnect MV Power.
  14. Install the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  15. Restore the LH front seat back to its original position.
  16. Install the LH upper A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Upper Trim - LH (Remove and Install).
  17. Install the LH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  18. Install the front header trim. See Headliner Trim - Front Header Trim (Remove and Install).
  19. Exit Service Mode.
  20. Raise all the windows and close all the doors.