23/07/2024 17:28:45

Front and Rear Door Latch and Striker - Door Latch - Rear LH (Remove and Install)

Correction code 1133041041 1133041042 1133041051 1133041052 FRT 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Place the vehicle into Service Mode. See Service Mode.
  3. Open the LH rear door and lower the LH rear window.
  4. Remove the LH rear beltline assembly. See Rear Door Trim Pad - Beltline Assembly - LH (Remove and Install).
  5. Remove the LH rear door inner waist belt seal. See Front and Rear Door Seals - Inner Waist Belt Seal, Rear Door, LH (Remove and Install).
  6. Use a pocket screwdriver to manually latch the LH front door.
  7. Raise the LH rear window.
  8. Remove the LH rear door trim. See Rear Door Trim Pad - Door Trim Rear - LH (Remove and Install).
  9. Remove the LH rear moving glass. See Door Glass - Moving Glass - Rear LH (Remove and Install).
  10. Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  11. Disconnect MV power. See Disconnect MV Power.
  12. Release the locking tabs and disconnect the LH rear door harness connectors (x4), and then release the clips (x5) that attach the harness to the LH rear door closeout panel.
  13. Remove the bolts (x13) and release the datums (x2) that attach the LH rear door closeout panel to the door assembly, and then remove the closeout panel from the door assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Gently pry the panel to release the datums (x2).
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the bottom portion of the panel away from the door assembly, and then lower the assembly to allow clearance for the regulator rails.
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
    • 10 mm socket
  14. Release the grommet that attaches the LH rear door latch to the door assembly, and then release the connector lock and disconnect the door latch electrical connector.
  15. Remove the bolts (x3) that attach the LH rear door latch to the door assembly, and then remove the latch from the assembly.
    13 Nm (9.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket

Install

  1. Position the LH rear door latch to the door assembly, and then install the bolts (x3) that attach the latch to the assembly.
    13 Nm (9.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket
  2. Connect the door latch electrical connector and engage the connector lock, and then install the grommet that attaches the door latch to the door assembly.
  3. Position the LH rear door closeout panel to the door assembly, and then install the bolts (x13) and datums (x2) that attach the closeout panel to the door assembly.
    4 Nm (2.9 lbs-ft)
    12 Nm (8.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Torque the 8mm bolts (x11) to 4 Nm, and the 10 mm bolts (x2) to 12 Nm.
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
    • 10 mm socket
  4. Connect the LH rear door harness connectors (x4) and secure the connector locks, and then install the clips (x5) that attach the harness to the LH rear door closeout panel.
  5. Connect an external window switch to the LH rear door.
  6. Position the LH rear door glass into the vehicle, and then install and hand tighten the bolts (x2) that attach the glass to the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be careful of the glass slipping off the mount.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  7. Install the LH rear door inner waist belt seal. See Front and Rear Door Seals - Inner Waist Belt Seal, Rear Door, LH (Remove and Install).
  8. Pull the emergency cable to manually unlatch the LH rear door.
  9. Reconnect MV power. See Disconnect MV Power.
  10. Install the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  11. Close the RH rear door.
  12. Check and adjust gap and flushness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Connect an external window switch to help with adjustment.
  13. Open the LH rear door.
  14. Torque the fasteners for window regulator, and then install the grommets (x2).
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  15. Disconnect the external window switch.
  16. Install the LH rear door trim. See Rear Door Trim Pad - Door Trim Rear - LH (Remove and Install).
  17. Install the LH rear beltline assembly. See Rear Door Trim Pad - Beltline Assembly - LH (Remove and Install).
  18. Raise the LH rear window and close the LH rear door.