2024-07-23
Door Presenter - Rear Door - LH (Remove and Replace)
Correction code
1133041082
1133041081
1133041092
1133041091
FRT
0.36
NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.
NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com.
NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.
Warning
This procedure is a DRAFT.
Although it has been validated, Warnings and Cautions might be missing. Follow safety
requirements and use extreme caution when working on or near High Voltage systems and
components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Warning
Cybertruck electronics are powered by a 48V "mid voltage" or "MV" architecture that is designed to improve efficiency. Servicing MV components requires extra knowledge and care in order to avoid personal and/or vehicular harm. Read and understand MV precautions in Electrical Precautions and make sure any required MV-related training courses have been completed, as applicable.
Remove
- Open the LH front door.
- Place the vehicle into Service Mode. See Service Mode.
- Remove the LH rear door moving glass. See Door Glass - Moving Glass - Rear LH (Remove and Install).
- Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
- Disconnect MV power. See Disconnect MV Power (Modify).
- Release the connector locks, and then disconnect the LH rear door harness electrical connectors (x4) from the closeout panel.
- Release harness clips (x5) that attach the LH rear door harness to the closeout panel.
-
Remove the fasteners (x13) that attach
the LH rear door closeout panel to the door.
TIpUse of the following tool(s) is recommended:
- 8 mm socket
- 10 mm socket
- Gently pry the LH rear door closeout panel away from the door assembly to the release the datums (x2), pull the bottom of the panel outwards, and then lower the assembly to clear the regulator rails.
-
Remove the bolts (x2) that attach the
LH rear door presenter to the door assembly.30 Nm (22.1 lbs-ft)TIpUse of the following tool(s) is recommended:
- Torx T30 socket
- Release the connector lock, and then disconnect the LH rear door presenter electrical connector.
- Release the LH rear door presenter from the clip, tilt the presenter counterclockwise to clear the door cutout, and then remove the assembly from the vehicle.
Install
- Position the LH rear door presenter into the vehicle, tilt the presenter clockwise to clear the door cutout, and then secure it onto the clip.
-
Install the bolts (x2) that attach the
LH rear door presenter to the door assembly.30 Nm (22.1 lbs-ft)NoteCheck alignment to ensure the presenter is centered in door cutout before tightening the fasteners.TIpUse of the following tool(s) is recommended:
- Torx T30 socket
- Connect the LH rear door presenter electrical connector, and then engage the connector lock.
-
Position the LH rear door closeout
panel into the vehicle, and then install the fasteners.4 Nm (2.9 lbs-ft)12 Nm (8.8 lbs-ft)NoteThe 8 mm bolts are torqued to 4 Nm. The 10 mm bolts are torqued to 12 Nm.TIpUse of the following tool(s) is recommended:
- 8 mm socket
- 10 mm socket
- Secure the harness clips (x5) that attach the LH rear door harness to the closeout panel.
- Connect the LH rear door harness electrical connectors (x4) to the closeout panel, and then engage the connector locks.
- Connect an external window switch.
-
Position the LH rear door glass into
the vehicle, and then install and hand tighten the bolts (x2) that attach the glass to
the vehicle.
CAUTIONBe careful of the glass slipping off the mount.TIpUse of the following tool(s) is recommended:
- 10 mm socket
- Pull the emergency cable to manually unlatch the LH rear door.
- Reconnect MV power. See Disconnect MV Power (Modify).
- Close the LH rear door.
-
Check and adjust gap and
flushness.
NoteConnect an external window switch to help with adjustment.
- Open the LH rear door.
-
Torque the fasteners for window
regulator, and then install the grommets (x2).13 Nm (9.6 lbs-ft)TIpUse of the following tool(s) is recommended:
- 10 mm socket
- Disconnect the external window switch.
- Install the LH rear door inner waist belt seal. See Front and Rear Door Seals - Inner Waist Belt Seal, Rear Door, LH (Remove and Install).
- Install the LH rear door trim. See Rear Door Trim Pad - Door Trim Rear - LH (Remove and Install).