23/07/2024 17:31:57

Interior Ducting and Vents - IP Aerobracket Assembly (Remove and Install)

Correction code 1405077071 1405077072 FRT 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the front doors and lower the front windows.
  2. Remove the LH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  3. Remove the LH lower A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Lower Trim - LH (Remove and Install)
  4. Remove the footwell cover. See Dash Support Frame - Footwell Cover (Remove and Install).
  5. Repeat steps 2 and 3 for the RH side of the vehicle.
  6. Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  7. Disconnect MV power. See Disconnect MV Power.
  8. Remove the mid instrument panel assembly. See Dash Panel - IP Mid Panel Assembly (Remove and Install).
  9. Remove the lower instrument panel assembly. See Dash Panel - Instrument Panel Lower Assembly (Remove and Install).
  10. Remove the glovebox assembly. See Dash Panel - IP Glovebox Assembly (Remove and Install).
  11. Remove the RH air wave duct. See Passenger Ducting and Vents - Panel Duct, RH (Remove and Install).
  12. Remove the front passenger airbag. See Front Air Bags - MX - Passenger Airbag, NAR (Remove and Install).
  13. Remove the instrument panel top pad assembly. See Dash Panel - Instrument Panel Top Pad Assembly (Remove and Install)
  14. Remove the clip that attaches the driver demist duct assembly to the IP aerobracket assembly.
  15. Disconnect the driver side IP airwave module electrical connectors (x2).
  16. Disconnect the IP aerobracket assembly light strip electrical connectors (x2).
  17. Remove the clip that attaches the passenger demist duct assembly to the IP aerobracket assembly.
  18. Disconnect the passenger side IP airwave module electrical connectors (x2).
  19. Remove the screws (x3) and release the tabs (x14) that attach the IP aerobracket assembly to the vehicle, and then remove the assembly from the vehicle.
    2.3 Nm (1.7 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be careful not to scratch the interior trim when removing the assembly from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket

Install

  1. Position the IP aerobracket assembly into the vehicle, and then secure the tabs (x14) and install the screws (x3) that attach the assembly to the vehicle.
    2.3 Nm (1.7 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be careful not to scratch the interior trim when installing the assembly into the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  2. Connect the passenger side IP airwave module electrical connectors (x2).
  3. Install the clip that attaches the passenger demist duct assembly to the IP aerobracket assembly.
  4. Connect the IP aerobracket assembly light strip electrical connectors (x2).
  5. Connect the driver side IP airwave module electrical connectors (x2).
  6. Install the clip that attaches the driver demist duct assembly to the IP aerobracket assembly.
  7. Install the instrument panel top pad assembly. See Dash Panel - Instrument Panel Top Pad Assembly (Remove and Install)
  8. Install the front passenger airbag. See Front Air Bags - MX - Passenger Airbag, NAR (Remove and Install).
  9. Install the RH air wave duct. See Passenger Ducting and Vents - Panel Duct, RH (Remove and Install).
  10. Install the glovebox assembly. See Dash Panel - IP Glovebox Assembly (Remove and Install).
  11. Install the lower instrument panel assembly. See Dash Panel - Instrument Panel Lower Assembly (Remove and Install).
  12. Install the mid instrument panel assembly. See Dash Panel - IP Mid Panel Assembly (Remove and Install).
  13. Reconnect MV power. See Disconnect MV Power.
  14. Install the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Install).
  15. Install the RH lower A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Lower Trim - LH (Remove and Install)
  16. Install the RH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  17. Install the footwell cover. See Dash Support Frame - Footwell Cover (Remove and Install).
  18. Repeat steps 15 and 16 for the LH side of the vehicle.
  19. Raise the front windows and close the front doors.