2026-03-03

Harness - Bed - RH (Long Range) (Remove and Install)

Correction code 17101201101 17101201102 2.58 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Warning

This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.

Warning

Cybertruck electronics are powered by a 48V "mid voltage" or "MV" architecture that is designed to improve efficiency. Servicing MV components requires extra knowledge and care in order to avoid personal and/or vehicular harm. Read and understand MV precautions in Electrical Precautions and make sure any required MV-related training courses have been completed, as applicable.

2026-02-26: Released new procedure.

Open LH front door

Note
Push LH B-pillar door trigger to release
Lower LH front window
Place the vehicle into Service Mode. See Service Mode.
Open LH rear door

Note
Push LH C-pillar door trigger to release
Lower LH rear window
Remove 2nd row floor mat
Open RH front door

Note
Push RH B-pillar door trigger to release
Lower RH front window
Open RH rear door

Note
Push RH C-pillar door trigger to release
Lower RH rear window
Open tailgate

Note
Press button to release, Use manual release as necessary
Open powered front trunk

Note
Via exterior switch or UI
Remove rear underhood apron

Note
9x clips
Disconnect first responder loop and MV battery connector

Note
2x connectors, Release locking tab then disconnect FRL connector, Slide eCPA to left then lift lever to release MV battery connector, Early production trucks may have black FRL connector, Release eCPA by pushing down to unlock and slide red locking tab, Wait 2 minutes for electrical circuits to discharge before disconnecting modules
Remove frunk assembly

Note
6x bolts, 10mm, 12 Nm, 2x bolt caps, 2x bumpstops, 1x connector, Remove bolt covers from frunk floor, Remove washer fluid cap by gently prying upwards, Rotate bumpstops counter clockwise to release, the 25mm socket from PT Sensor kit can be used, Avoid straining emergency frunk release connector
Remove RH underhood apron

Note
3x clips
Remove front nut securing RH cantrail

Note
1x nut, 8mm, 4 Nm, Discard after removal
Remove RH sail baffle applique

Note
3x clips, Release clips working from bottom upwards
Remove RH sail baffle closeout

Note
6x clips
Remove RH C pillar applique closeout

Note
2x clips
Remove RH C pillar applique

Note
1x connector, 2x clips, 1x bolt, 10mm, 6 Nm, Pull outwards from bottom then pull down to release
Remove RH header seal

Note
Seal begins at front quarter glass and ends at C-pillar applique, Start at C-pillar, Pull B-pillar applique down gently to release seal, Pull outwards to release seal from carrier grooves
Remove screws securing RH cantrail

Note
8x screws, T20, 2.5 Nm, Pull C-pillar applique down as required for access
Remove RH cantrail assembly

Note
7x clips, Recommend assistance, Pull away from body side to release clips, Place on padded surface
Remove RH rear fender flare

Note
18x clips
Remove clips securing RH rear wheel liner to aft fender flare carrier

Note
2x clips
Remove clips securing RH rear wheel liner to fore fender flare carrier

Note
5x clips
Remove RH rear aft fender flare carrier

Note
2x bolts, 10mm, 7 Nm
Remove RH rear fore fender flare carrier

Note
6x bolts, 10mm, 7 Nm, 1x connector, Disconnect BLE module then remove carrier, Release locking tab
Remove fastener covers from bed floor assembly

Note
14x covers
Remove bed floor assembly

Note
10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Lift front edge with trim tool then remove panel, Recommend assistance
Remove LH lower bed side wall

Note
2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers
Remove RH sail applique

Note
15x clips
Remove the RH bed closeout panel
Remove RH bed closeout panel

Note
6x clips, 1x tab, Release RH tailgate cable by disengaging lock spring from bolt and sliding cable eyelet off in order to remove bed closeout panel from vehicle
Remove RH bed side wall

Note
2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers
Release RH tail lamp applique

Note
2x clips, 2x datums
Remove RH outer bed side

Note
13x bolts, 13mm, 28 Nm, 1x screw, T30, 8 Nm, Assistance required, Have assistant hold bed side to body while bolts are removed, Place on padded surface once removed
Remove RH mid A-pillar trim

Note
1x clip, 3x tabs, Release tabs then slightly bend live hinge and release clip
Remove RH upper A-pillar panel

Note
8x clips, 1x harness clip, 1x connector, 1x bolt, 10mm, 6 Nm, Pull inwards to release
Push open RH coat hook

Note
Press to release
Remove RH coat hook bolt cover

Note
2x tabs
Remove RH coat hook bolt

Note
1x bolt, T20, 2.5 Nm
Remove RH cantrail trim panel

Note
5x clips, 1x connector, 3x bolts, T30, 6 Nm, Release clips then allow cantrail to hang from tethers for access to fasteners
Fold up 2nd row 60 seat

Note
Pull tether to release then lift up until locked in place
Partially release LH lower C-pillar trim

Note
1x clip, 1x datum
Fold up 2nd row 40 seat

Note
Pull tether to release then lift up until locked in place
Partially release RH lower C-pillar trim

Note
1x clip, 1x datum
Remove rear wall lower trim

Note
2x push clips, 4x clips, Remove outermost push clips, then pull straight forward to release inner clips
Remove RH Upper C-pillar

Note
5x clips, 3x tabs
Release RH 2nd row shoulder cover

Note
7x clips, 1x datum
Remove clip securing RH 2nd row seat outboard B cover assembly

Note
1x clip, Position aside for access to clip
Remove RH 2nd row seat back assembly

Note
2x push clips, 4x clips, 1x connector, 3x bolts, 10mm, 9 Nm, Pull upwards then away from frame then disconnect electrical harness, Release locking tab
Remove LH rear aft fender flare

Note
5x clips
Remove clips securing LH rear wheel liner onto rear fascia and diffuser

Note
5x clips
Remove clips securing LH rear wheel liner to aft fender flare carrier

Note
2x clips
Remove LH rear aft fender flare carrier

Note
2x bolts, 10mm, 7 Nm, 2x datum
Remove license plate

Note
4x screws, Phillips PH2, 1 Nm
Remove bolts securing rear center fascia onto body

Note
2x bolts, 10mm, 6 Nm
Remove clips securing RH rear wheel liner onto rear fascia and diffuser

Note
5x clips
Remove bolts securing rear diffuser onto body

Note
9x bolts, 10mm, 6 Nm
Disconnect rear fascia harness connector

Note
1x connector, Release locking tab, Harness is located behind rear of LH rear wheel liner
Remove rear fascia from vehicle

Note
16x tabs, Release RH and LH side of rear fascia from body, Remove rear fascia from vehicle, Recommended assistance, Place onto protected surface
Remove RH rear wheel liner

Note
19x push clips, 5x push nuts, Discard push nuts after removal
Release rear lower section of RH bed harness

Note
1x connector, 5x clips, Release clip at opening near rear fascia bracket then pull harness through, Release locking tab
Release rear upper section of RH bed harness

Note
2x connectors, 11x clips, Release locking tabs
Release mid section of RH bed harness

Note
8x clips
Release ancillary section of RH bed harness

Note
3x connectors, 3x clips, Disconnect from HV battery ancillary passthrough, Disconnect height sensor, Release locking tabs
Release front section of RH bed harness

Note
1x connector, 8x clips, 1x bolt, 10mm, 7 Nm, Release locking tab
Release interior section of RH bed harness

Note
1x connectors, 12x clips, 1x grommet, 1x bolt, 8mm, 4 Nm, Do not remove locking cover, Loosen until bolt spins freely, Double check that bolt and locking cover are fully released before attempting to release any MV connectors, Depress tabs to release grommet, Release locking tabsPlastic Locking Cover Use hand tools on any plastic locking covers, The locking cover may release crooked causing it to get stuck, secure bolt a few turns to loosen the tension then release bolt while assisting plastic locking cover by gently prying on the side that's stuck Metal Locking Cover You can use power tools, Quickly disconnecting locking cover helps connectors remove symmetrically
Remove RH bed harness

Note
Pull harness through from interior
Position RH bed harness

Note
Push harness through to interior
Secure interior section of RH bed harness

Note
1x connector, 12x clips, 1x grommet, 1x bolt, 8mm, 4 Nm, Ensure connectors are aligned before securing bracket, Secure locking cover bolt by hand initially to prevent thread stripping, Secure grommet by pushing inwards, Engage locking tabsPlastic Locking Cover Use hand tools on any plastic locking covers, The locking cover may secure crooked causing it to get stuck, release bolt a few turns to loosen the tension then secure bolt while assisting plastic locking cover by gently pushing on the side that's stuck, Push connectors while driving the locking cover bolt to ensure correct seating Metal Locking Cover You can use power tools, Slowly drive locking cover, Ensure locking cover and bolt are seated fully
Secure front section of RH bed harness

Note
1x connector, 8x clips, 1x bolt, 10mm, 7 Nm, Engage locking tab
Secure ancillary section of RH bed harness

Note
3x connectors, 3x clips, Connect HV battery ancillary passthrough, Connect height sensor, Engage locking tabs
Secure mid section of RH bed harness

Note
8x clips
Secure rear upper section of RH bed harness

Note
2x connectors, 11x clips, Engage locking tabs
Secure rear lower section of RH bed harness

Note
1x connector, 5x clips, Push harness through opening near rear RH fascia bracket then secure clip, Secure locking tab
Install RH rear wheel liner

Note
19x push clips, 5x push nuts, Install new push nuts, Use of a socket and dead blow hammer can aid installation
Install rear fascia onto vehicle

Note
16x tabs, Recommend assistance, Sides will need to be spread apart to clear bumper structure
Install bolts securing rear center fascia onto body

Note
2x bolts, 10mm, 6 Nm
Install license plate

Note
4x screws, Phillips PH2, 1 Nm
Install bolts securing rear diffuser onto body

Note
9x bolts, 10mm, 6 Nm
Install rear fascia connector

Note
1x connector, Secure locking tab
Install clips securing LH rear wheel liner onto rear fascia and diffuser

Note
5x clips
Install LH rear aft fender flare carrier

Note
2x bolts, 10mm, 7 Nm
Install clips securing LH rear wheel liner to aft fender flare carrier

Note
2x clips
Install LH rear aft fender flare

Note
5x clips, Replace any damaged or missing clips
Install clips securing RH rear wheel liner onto rear fascia and diffuser

Note
5x clips
Install RH 2nd row seat back assembly

Note
2x push clips, 4x clips, 1x connector, 3x bolts, 10mm, 9 Nm, Connect electrical harness before fully seating assembly, Engage locking tab
Install clip securing RH 2nd row seat outboard B cover assembly

Note
1x clip, Ensure strap is not twisted
Install RH 2nd row shoulder cover

Note
7x clips, 1x datum
Install RH Upper C-pillar

Note
5x clips, 3x tabs
Install rear wall lower trim

Note
2x push clips, 4x clips
Secure LH lower C-pillar trim

Note
1x clip, 1x datum
Fold down 2nd row 60 seat

Note
Pull tether to release then pivot down until locked in place
Install RH lower C-pillar trim

Note
1x clip, 1x datum
Fold down 2nd row 40 seat

Note
Pull tether to release then pivot down until locked in place
Install 2nd row floor mat
Secure RH cantrail panel

Note
5x clips, 1x connector, 3x bolts, T30, 6 Nm, Secure tethers then secure clips
Install RH coat hook bolt

Note
1x bolt, T20, 2.5 Nm
Install RH coat hook bolt cover

Note
2x tabs
Close RH coat hook

Note
Press to secure
Install RH upper A-pillar panel

Note
8x clips, 1x tether clip, 1x edge clip, 1x connector, 1x bolt, 10mm, 6 Nm, Ensure tethers are correctly oriented, Replace any missing or damaged clips
Install RH mid A-pillar trim

Note
1x clip, 3x tabs, Replace any missing or damaged clips
Install RH outer bed side

Note
13x bolts, 13mm, 28 Nm, 1x screw, T30, 8 Nm, Assistance required, Have assistant hold panel against body then install bolts hand tight, Adjust gap and flush as required then torque bolts
Install LH body side tail lamp

Note
1x connector, 2x datums, 2x bolts, T30, 5 Nm, Push forwards to engage datums, Engage locking tab
Secure RH tail lamp applique

Note
2x clips, 2x datums
Install RH bed side wall

Note
2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers
Install RH bed closeout panel

Note
6x clips, 1x tab, Release RH tailgate cable to install bed closeout panel from vehicle
Install RH upper bed side wall assembly

Note
13x clips, Replace any missing or damaged clips
Install RH sail applique

Note
13x clips, Replace any damaged clips
Install bed floor assembly

Note
10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Recommend assistance
Install fastener covers onto bed floor assembly

Note
14x covers
Install LH rear fore fender flare carrier

Note
6x bolts, 10mm, 7 Nm, 1x connector, Connect BLE then install carrier, Engage locking tab
Install RH rear aft fender flare carrier

Note
2x bolts, 10mm, 7 Nm
Install clips securing LH rear wheel liner to fore fender flare carrier

Note
5x clips
Install clips securing RH rear wheel liner to aft fender flare carrier

Note
2x clips
Install RH rear fender flare

Note
18x clips, Replace any missing or damaged clips
Install RH cantrail assembly

Note
7x clips, Recommend assistance, Vehicles may be equipped with 10 or 11 clips in production range
Install screws securing RH cantrail

Note
8x screws, T20, 2.5 Nm, Pull C-pillar applique down as required for access
Install RH header seal

Note
Start from front quarter glass, Push upwards into seal carrier grooves
Install RH sail baffle closeout

Note
6x clips, Replace any missing or damaged clips
Install LH C pillar applique

Note
1x connector, 2x clips, 1x bolt, 10mm, 6 Nm, Slide upwards then push inwards to secure clip,
Install LH C pillar applique closeout

Note
2x clips
Install LH sail baffle applique

Note
3x clips, Replace any missing or damaged clips
Install nut securing RH front outer cantrail

Note
1x nut, 8mm, 4 Nm, Install new nut
Install RH underhood apron

Note
3x clips
Connect first responder loop and MV battery connector

Note
2x connectors, Connect FRL connector then secure locking tab, Position lever to secure MV battery connector then slide eCPA to right, Early production trucks may have black FRL connector, If power cycling vehicle then ensure at least 60 seconds has passed since powering down
Install frunk assembly

Note
6x bolts, 10mm, 12 Nm, 2x bolt caps, 2x bumpstops, 1x connector, Install bolt covers to frunk floor, Install washer fluid cap, Install bumpstops by aligning tabs then turning clockwise, Ensure emergency frunk release functions
Install rear underhood apron

Note
9x clips, Adjust windshield seal as required
Close powered front trunk

Note
Via exterior switch or UI
Run ODIN routine
Close tailgate
Close all four doors
Raise all 4 windows

Note
Verify switch is operating as expected

Cybertruck Service Manual

Harness - Bed - RH (Long Range) (Remove and Install)

Figure 1

Figure 2

Figure 3